Cylinder Cutout Test using Caterpillar ET Software

How to perform Cylinder Cutout Test using CAT ET Diagnostic Software?

Purpose:
The cylinder cutout test allows one cylinder or multiple cylinders to be cut out. The cylinder cutout test is useful when troubleshooting poor engine performance or a suspected injector failure.
Test Operation:
The cylinder cutout test disables the injector by not providing the injector pulse to the solenoid. The cylinder cutout test can be performed on one injector or multiple injectors at once.

-Connect to CAT ET Software,
-Open Menu: Diagnostics – Diagnostic Tests – Cylinder Cutout Test

Cylinder-Cutout-Test-using-Caterpillar-ET-Software-1

-Click Start, then Select Cylinder Cutout Test

Cylinder-Cutout-Test-using-Caterpillar-ET-Software-2
-Click Continue, then OK

Cylinder-Cutout-Test-using-Caterpillar-ET-Software-3

-Wait until All Cycle Test (Cylinder 1-6) finished, and look at the Results on Fuel Position tab, the smallest value than the others, indicates that could be damaged on Injector.

Cylinder-Cutout-Test-using-Caterpillar-ET-Software-4

NOTE:
1-Cylinder Cutout Test Conditions,
The following conditions must be met for the Automatic Cylinder Cutout Test
1) Engine Speed must be between 980 RPM and 1020 RPM (Engine Speed will automatically adjusted)
2) Engine Coolant Temperature must be 170 Deg F or higher
3) No Engine Performance related active diagnostic codes are allowed
4) No default Injector Serial Number (000000000000) allowed
5) Throttle position must not vary by +/- 5%

Cylinder-Cutout-Test-using-Caterpillar-ET-Software-5

If at any time any of these conditions are not met, the test will automatically aborted.
-Ensure Transmission is in Neutral or Electrical Load is removed from Generator.
-Fan cycling, A/C compressor cycling, or changes in Engine Load will invalidate this test.
-If the fan is not controlled by the Engine ECM, please Enable the fan if possible.
-WARNING: If the ECM controls the fan, the fan will be turned ON automatically upon starting this test.
-WARNING: Please make sure the Compression Brake is in the OFF position. During the test, Compression Brake operation will cause the Engine to surge.

Cylinder-Cutout-Test-using-Caterpillar-ET-Software-6

Manual Cylinder Cutout Test
-Click on Change – Start – Stop tab, and look at Fuel Position value.

Cylinder-Cutout-Test-using-Caterpillar-ET-Software-7

Cat Electronic Technician Diagnose. Communicate. Repair

Caterpillar Electronic Technician (ET) is a software-based service tool which provides service technicians the ability to communicate and work with the electronic controls on Cat products.

Cat-Electronic-Technician-1

Cat Electronic Technician allows you to:

Display status parameters
View active diagnostic codes
View and clear logged diagnostic codes
Manipulate ECM configuration
Record machine information over a period of time
Run diagnostic tests and calibrations
Retrieve machine totals

If you would like to purchase Cat ET, or email sale@cnautotool.com.

*Cat Electronic Technician (ET) license requires annual renewal. A communications adapter is required to connect a computer to the equipment or engine. We cannot sell or license ET outside Virginia or Southern West Virginia.

CAT SIS 2019 shows 404 error page solution:

CAT-SIS-2019-shows-404-error-page-solution-1

CAT-SIS-2019-shows-404-error-page-solution-2

CAT-SIS-2019-shows-404-error-page-solution-3

As shown above, after clicking the engine model, the 404 error page is resolved:

1. First, close the SIS to exit the system.

CAT-SIS-2019-shows-404-error-page-solution-4

2. Open Network Connections, open D:\CAT SIS 2019\Caterpillar SIS 01.2019\Crack\Crack folder, right click to run CAT SIS Network ID file as administrator, copy Serial
After the ID, click Apply Serial.

CAT-SIS-2019-shows-404-error-page-solution-5

3. Right-click to run Keygen as the administrator, fill the copied Serial ID into the Host ID, delete the middle space of the ID, and click Generate to get the new license.dat file.

CAT-SIS-2019-shows-404-error-page-solution-6

4. Copy the license.dat file to the C:\Caterpillar folder and paste it to replace the original file. Re-open the SIS.

Solution CAT SIS 2019 fail to display pictures

If you purchased the CAT SIS 2019 software from Cnautotool.com,
having problems with the software not being able to display images,
You can follow our steps to operation.

Solution-CAT-SIS-2019-fail-to-display-pictures-1

CAT SIS 2019 must use the Internet explorer browser built into the computer system to display images properly.

Solutions:

Windows 7 Default browser Settings:

Step 1. Select “Default Programs”
Solution-CAT-SIS-2019-fail-to-display-pictures-2

Step2 : Set Your default programs

Solution-CAT-SIS-2019-fail-to-display-pictures-3

Step 3 : Select “ Internet explorer “ — “Set this program as default “ —-“ok”
Solution-CAT-SIS-2019-fail-to-display-pictures-4

If you still have problem to work, Please contact our sales : https://www.obd2tool.com/article-50-Contact+us.html

How to Communication Hardware with Caterpillar Communication Adapter III


Configuring Cat Electronic Technician to use the Communication Adapter 3
For Cat Electronic Technician to work with the Communication Adapter 3, the settings must be changed to select the Communication Adapter 3 as the Communication Interface Device:
Step 1 : Start Cat Electronic Technician.
Step 2 :  Click the Stop Connect button when it appears.
Step 3 : Select the Utilities menu.
Step 4 : Choose “Preferences > Modify…”.
Step 5 : Select the Communications tab.
Step 6 : Select Cat Comm Adapter 3 (RP1210) and click OK.
NOTE: Because a growing number of products require multiple data link service, the “Enable Dual Datalink Service” checkbox has been pre-selected.
Servicing ECMs on more than one data link requires this check box to be enabled.
Failure to do this will result in undetected ECMs and reduced functionality.

Any request for CAT Caterpillar ET Diagnostic Adapter III , welcome to contact us any time

www.cnautotool.com

sale@cnautotool.com

How to Solve the Problem NEXIQ-2 USB Link + Software can’t run keygen ?

NEXIQ-2 Support Heavy-Duty, Light-and Medium-Duty Trucks, CONSTRUCTION EQUIPMENT like (Wheel loader, Articulated Hauler and Excavator), Genset.

Some customers have the problem that the software can’t run keygen , please check the pictures as bellow :

Need to active :

Cummins insite 7.5 :

Pc id : 43873FA7

Caterpillar E.T . :

License code : 3295 668C 8D56 CE1E CD16 4E7C

DDDL :

 

Version : 07.05-01301-00000

Computer ID : E8-BE-28-1E-2D

Solution:

DDDL doesnt need to active but operate in the crack method ( You can check the instructions in the CD )

Any other request , welcome to contact us at sale@cnautotool.com

Or check more products on our website www.cnautotool.com

 

Scania VCI-3 VCI3 Scanner Installation and Testing

How to install the software for Scania VCI-3 ?

Lets check the steps as bellow :
Install on Windows 7 32/64 bit
1)Install run admin mode — Prerequisites.bat

2) Restart — (you must leave the mode enabled, but only win 7 64 bit, in Win 7 32 bit it is not necessary)
3) Install NDP462-KB3151800-x86-x64-AllOS-ENU AdbeRdr920_en_US

4)Install Sdp3 2.40.1


5) Install driver 32 or 64 Bit
6) Run “Hardware ID Reader” copy ID machine

7)Run “Protection REG” paste up ID machine —> click in “Decode Fingerprint” —> click in “Generate” —> a .reg file is generated in the folder

8) Run clik .reg file and apply
9) Copy and replace in the program folder 2 file “Fix File 2.39.1″
10) Run install “ScaniaSDP3Time”
11) Restart PC

For upgrading the previous version
1) Install Sdp3 2.39.1
2) Copy and replace in the program folder 2 file “Fix File 2.39.1″
if during the installation it crashes, uninstall in the programs — Kvaser Can Driver WHCP and re-install Sdp3 2.39.1

More details you can check the Scania vci3 video here

Testing for Scania vci-3

Video for testing

More request for Scania VCI-3 VCI3 Scanner Wifi Wireless Diagnostic Tool , welcome to contact us directly
www.cnautotool.com
sale@cnautotool.com

Cylinder Cutout Test using Caterpillar ET Software

How to perform Cylinder Cutout Test using Caterpillar ET Software?

Purpose:
The cylinder cutout test allows one cylinder or multiple cylinders to be cut out. The cylinder cutout test is useful when troubleshooting poor engine performance or a suspected injector failure.
Test Operation:
The cylinder cutout test disables the injector by not providing the injector pulse to the solenoid. The cylinder cutout test can be performed on one injector or multiple injectors at once.

-Connect to CAT ET Software,
-Open Menu: Diagnostics – Diagnostic Tests – Cylinder Cutout Test

二张-1

-Click Start, then Select Cylinder Cutout Test
for Example: choose 1-Cylinder Cutout Test

二张-2

-Click Continue, then OK

二张-3

-Wait until All Cycle Test (Cylinder 1-6) finished, and look at the Results on Fuel Position tab, the smallest value than the others, indicates that could be damaged on Injector (for Example: Cylinder 1).

二张-4

NOTE:
1-Cylinder Cutout Test Conditions,
The following conditions must be met for the Automatic Cylinder Cutout Test
1) Engine Speed must be between 980 RPM and 1020 RPM (Engine Speed will automatically adjusted)
2) Engine Coolant Temperature must be 170 Deg F or higher
3) No Engine Performance related active diagnostic codes are allowed
4) No default Injector Serial Number (000000000000) allowed
5) Throttle position must not vary by +/- 5%

二张-5

for Example: 1-Cylinder Cutout Test Aborted

If at any time any of these conditions are not met, the test will automatically aborted.
-Ensure Transmission is in Neutral or Electrical Load is removed from Generator.
-Fan cycling, A/C compressor cycling, or changes in Engine Load will invalidate this test.
-If the fan is not controlled by the Engine ECM, please Enable the fan if possible.
-WARNING: If the ECM controls the fan, the fan will be turned ON automatically upon starting this test.
-WARNING: Please make sure the Compression Brake is in the OFF position. During the test, Compression Brake operation
二张-6

will cause the Engine to surge.
for Example: 1-Cylinder Cutout Test Aborted

Manual Cylinder Cutout Test
-Click on Change – Start – Stop tab, and look at Fuel Position value.

二张-7

Injector Solenoid Test using Caterpillar ET Software

How to perform: Injector Solenoid Test using CAT ET Software (CAT Engine)?
The purpose of the injector solenoid test is to diagnose injector wiring and injector solenoid functionality.

-Connect Caterpillar ET to your Laptop,
-Open Menu: “Diagnostics – Diagnostic Test – Injector Solenoid Test”
Example: CAT Engine – C11

Injector - Solenoid - Test - 1

NOTE: Injector Solenoid Test cannot be performed while the engine is running.

-Click “Power All” and wait the process until complete (Mode: powered), from Cylinder 1 to Cylinder 6.
-On Menu “Test Results”, all the results are OK, indicates that Solenoid Injector still on good condition.

Injector - Solenoid - Test - 2

NOTE:
-This test identifies an open circuit or a short circuit in the circuit for the injector solenoids. The test activates the injector solenoids one at a time while the engine is not running. A good solenoid will create an audible click when the solenoid is activated. Heavy Duty Diagnostic tool Cat ET indicates the status of the solenoid as “OK”, “Open”, or “Short”.

What diagnostic adapter do you prefer (Read 10626 times)

Tell you what adapter people use most. Here are views after the vote in the forum dedicated to all’s favorite adapter to share pros and cons and learn tips and tricks.

Here is my 2cents or 2.03cents Canadian on Diagnostic Interfaces.

DG Tech DPA4 or 4+: #2 Choice Metal case makes it durable (must use original USB cable to take advantage of USB port protection)

Nexiq USB-Link: #1 Choice can also be used with toyota techstream and isuzu IDSS (Must be very careful to not break the usb port on older style)

Nexiq Magikey: Was the best back in the day (Need a PC with printer port to connect)

Nexiq LiteLink: Works with Snapon Modis (older J1708 Data Bus only)

Cummins Inline: RP1210a compliant for apps other than Cummins Insite (Doesnt work well with all rp1210a applications)

Movimento/Navlink: Only way to connect to TCU via IDS on Ford/Int LCF/CF Trucks??? (Freezes using servicemax on some laptops)

Navistar IC4: Small durable adapter (Bad customer support, hard to find drivers, USB cable is part of adapter)

Older PF-Diagnose adapter (B&B Electronics): Small durable adapter (serial cable connection)

Eaton Wireless: Long wireless range (intermittent data loss even at close range)

Noregon DLA: #3 Choice alternative to Nexiq and Dearborn (Large size/odd shape)

Caterpillar II: Only way to connect to some offroad equipment with CDL data Bus (Need PC with printer port)

This is just my opinion on the CAT Caterpillar ET above based on personal use.

There are other adapters available and other peoples results/opinions may differ.