Obdstar X300 DP Plus Configuration A vs Configuration B vs Configuration C

What is OBDSTAR X300DP PLUS Configuration A, B, C?
8-0

It’s a new OBDSTAR OBD2 tool built with Android-based, used for vehicle diagnosis, coding, programming (key programming and ecu programming) and special functions (incl. odometer correction). It inherits from OBDSTAR advanced diagnosing technology and it is characterized by covering wide range of vehicles, featuring powerful function, and providing precise result. Through vehicle diagnostic OBD connector and variant mobile intelligent terminals, it achieves vehicle trouble diagnosis for full car model and full system vehicle.

There are three versions of Obdstar X300 DP Plus:

Configuration A, B and C coming with different features/function.

Look at the chart below in detail…

Obdstar X300 DP Plus Configuration A vs Configuration B vs Configuration C

8-1
X300 DP Plus A Package – used as a universal key programmer for locksmiths

Immobilizer+Special function(EEPROM+Key Renewing)Adapter(P001 programmer+C001circuit board+C002 circuit board+W001 cable+W002 data cable+W003 data cable+Toyota smart key Emulator)+others(Ignition coil+Remote tester)

X300 PAD2 B Package – works as an auto key programmer and a odometer correction tool

Immobilizer+Special function(EEPROM+Key Renewing)+Mileage correction+Adapter(P001 programmer+C001 circuit board+C002  circuit board+W001 data cable+W002 data cable+W003 data cable+Toyota smart key Emulator)+others(Ignition coil+Remote tester)

X300 DP Plus C Package – is a 3-in-1 tool for auto repair shops (auto diagnostic tool + car key programmer + programming tool for special functions)

Immobilizer+Mileage correction+Diagnosis+Special function (Oil reset +ABS+Battery matching+ECU programming+EPB+Throttle programming+Airbag rest+TPMS+Steering angle reset+OBDII+DPF+Injector code+Suspension matching+Gear learning+CVT learning+EEPROM+Key renewing+ECU cloning)Adapter(P001 programmer+C001 circuit board+C002 circuit board+W001 data cable+W002 data cable+W003 data cable+Toyota smart key Emulator)+others(Ignition coil+Remote tester)

IMPORTANT: OBDSTAR X300 DP Plus Immobilizer Car List

European cars:

VW/Audi/Skoda/Seat: Configuration C is able to program new keys to NEC 24C64 2014- (Configuration A is NOT able to…)

BMW: Configuration C is able to program FEM/BDC keys and read ISN codes (Configuration A is NOT able to…)

VOLVO: All X300 DP Plus versions CAN program/add new keys to Volvo

Also, X300 DP Plus A, B, C versions supports other cars made in Europe but not mention here…

Asian cars:

Hyundai/Kia: Configuration C is able to read pin codes of 47/8A/46 smart keys (Configuration A is NOT able to…)

Toyota/Lexus: The middle western version is able to program a new key with a H chip when all keys are lost (with the immo box reset)

Also, X300 DP Plus A, B, C versions supports other cars made in Asia but not mention here…

American cars:

Ford: Configuration C is able to program new keys to post-2015 Ford such as Mondeo, Edge, Taurus, ESCORT, Everest, Explorer, Raptor F-150, Raptor F-250, Mustang, Lincoln MKZ, MKC, Continental 2015 – etc. (Configuration A is NOT able to…)

GM: Configuration C is able to read BCM password of Buick LaCrosse (pre-2017), Envision, Trax, GL8, Malibu, Chevrolet Aveo, Excelle (pre-2015), Cruze, etc.  (Configuration A is NOT able to…)

Also, X300 DP Plus A, B, C versions supports other cars made in America but not mention here…

YOU HAVE TO KNOW: Why you should have a new Obdstar X300DP Plus instead of the old X300 DP and Lonsdor K518ISE?

Obdstar X300DP Plus vs OBDSTAR X300 DP:

X300 DP Plus has been improved a lot in hardware and supports more functions especially Toyota smart key card program and 8-pin chip data read.

In detail..

Obdstar X300DP Plus vs Lonsdor K518ISE:

Lonsdor k518ise is a tool for key programming only! It’s for locksmiths.

Obdstar x300 dp plus is a tool with diagnosis, immo and special functions 3 in 1. it’s a good helper to auto repair shops.

Program Passat 4th IMMO Key with OBDSTAR X300 DP

Here is the instruction on programming VAG Passat 4th IMMO Key by using OBDSTAR X300 DP key programmer and OBDSTAR RFID Adapter (adapter chip reader for VAG 4th 5th IMMO function)

Guide:
Dissemble the dashboard instrument
Connect OBDSTAR X300 DP with VCI and Dash
Turn ignition on (If it is the smart key, turn ignition OFF then turn it ON)

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-1.jpg
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-2.jpg
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-3.jpg

Make sure dash instrument is black

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-4.jpg
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-5.jpg

Reading eeprom data
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-6.jpg
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-7.jpg

Save data
Read IMMO data
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-8.jpg

Turn ignition on (If it is the smart key, turn ignition OFF then turn it ON)
Make sure dash instrument is black
Read VIN, CS code and PIN and key info

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-9.jpg
Select Generate OEM Dealer Key (Can start car)
Turn ignition on
Connect OBDSTAR RFID adapter with X300 DP

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-10.jpg
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-11.jpg

Insert the original key (chip) into RFID adapter

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-12.jpg
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-13.jpg

RFID Indicator flashes, remove the first key chip
Follow X300 DP prompt to insert second key chip
RFID indicator flashes, reading key data
dash indicators turn on

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-14.jpg

Generating dealer key in progress

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-15.jpg

Generate dealer key success

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-16.jpg
Test the new key, it works!