How to configure microPod using Wireless Configuration Utility

1.Connect a PC or Laptop that has the wiTECH MicroPod 2 installed to the wiTECH Access Gateway in ports 3 or 4 (preferred) you may also connect to the wiTECH wireless.
* Note: If PC or Laptop is not on the wiTECH network you may encounter discovery issues of the tools and or wiTECH Diagnostic Antenna.

2.Connect the microPOD with a USB cable to your PC or Laptop, wait for the USB drivers to install
* Note: If PC being used does not have the wiTECH application installed you will need to install the wiTECH application
* Note: If drivers do not load when the USB cable is plugged in you will need to move the USB cable to another USB port on the PC, or you may need to try another PC

3.Download the Wireless Configuration Utility from,
* log in, browse to Manage Assets > Wireless Configuration


4.Select the link Click here to Download VCI Pod and microPOD Wireless Configuration Utility and save the configuration utility to your desktop


5.Select the Generate Config PIN button


6.The PIN generator will create a 2 to 4 digit number as shown below


7.Locate and Launch the file wiTECH_Wireless_Config_Utility_1.1  on your desktop  8-5

Note:  this file may have been saved to your Downloads folder

8.Select Run


9.Enter your dealer code, and select OK


10.Enter the PIN number that was sent to your email address , and select OK


When the discovery screen for the tools opens you will need to make sure that you are seeing the microPOD that you are configuring

Note: If no tool is shown:

* Unplug the USB cable for the microPOD and plug into a different USB port
* Close the Configuration Utility and launch the utility again
* Try a different PC

microPOD Configuration steps

1.Select Auto Scanner Tool microPOD Configuration from the File menu in the upper left corner


2.Select the appropriate Country Code from the drop down menu


3.Enter the wiTECH wireless credentials
* WPA Passphrase
* Confirm Passphrase

4.Select Next

5.A series of commands will run – the end result will be Configuration complete, device rebooted. Configuration application will close. Select Ok


6.Unplug the microPOD from the USB cable and Plug the tool in to a supported vehicle to test
7.Launch wiTECH application – verify that the device is seen in discovery

Converting a microPod from wiTECH 2.0 to wiTECH 1.0


Note: The wiTECH MicroPod 2 Application has been deployed to only FCA-franchised dealers in the US and Canada.

As of April 28, 2016, due to new registration requirements, a microPod device will no longer be compatible with wiTECH 1.0 after it is registered with wiTECH 2.0.

Once a device is registered for wiTECH 2.0, it can no longer be converted to be used with wiTECH 1.0 again. We highly recommend assigning a dedicated microPod device to be used with wiTECH 1.0 when needed.


microPod II devices are a cost-effective diagnostic solution for your dealership. We strongly recommend that your dealership purchases an adequate number of microPods for your technicians. To purchase additional microPods, you can login to and go to Order Products > Begin Shopping > wiTECH Products > wiTECH Diagnostic Extender microPod II.

Chrysler Witech Micropod II Program 2014 Jeep Wrangler Add New Keys

Chrysler Witech Micropod II online version hot sale on, some custom order wiTECH micropod 2 from other supplier and stop work, we can offer wiTECH Chrysler diagnostic software installation service make wiTECH micropod 2 restart work. Or order wiTech Micropod 2 from directly. Below customer share how to use wiTECH Micropod II add new key for 2014 Jeep Wrangler.

SUCCESS! Everything worked.
I was able to program the second key to my Jeep. You are amazing and I cannot thank you enough. Here is what I did on my 2014 Jeep Wrangler:
Situation: My Jeep came with only ONE key and I wanted a second key.
You must have Witech 16.05.15 or older installed. Witech 17 gave me errors about requiring Witech 2.0.
First try: (Failed, did not work)
Step 1) No key in the ignition, plugged in wiTECH Micropod 2 to OBDII port.
Step 2) Connected Micropod 2 to laptop via USB cable.
Step 3) Opened Witech and it asked me to identify my Jeep and enter my VIN.
FAILED at this point. It required internet connection to validate the VIN and asked me to log into Dealer CONNECT or Tech Authority.
Second try (SUCCESS!!)
Step 1) No key in the ignition, plugged in Micropod 2 to OBDII port.
Step 2) Put my single good key in the ignition and put it to the RUN position.
Step 3) Connected Micropod 2 to laptop via USB cable.
Step 4) Opened Witech and left it offline.
Step 5) Opened WCM, then Misc. Functions, then Program FOBIK
Step 6) Entered my dealer supplied PIN.
Step 7) Removed old key and inserted new key.
Step 8) Be happy I now have two working keys to my Jeep.

Any need for Chrysler wiTECH Micropod 2 Chrysler diagnostic tool Mopar Micropod 2 just contact us freely

Thank you

CNautotool team

How to Set up wiTech MicroPod 2 Chrysler Diagnostic Tool

This is a how-to guide of wiTECH MicroPod 2 Chrysler diagnostic tool setup.

If your dealership purchased a new microPOD and you would like to convert your existing microPOD for using with wiTECH 2.0 System, you need to download and install the microPOD Setup Utility to configure/setup your microPOD for wiTECH 2.0.

NOTE: microPODs with a serial number beginning with “WFP” should NOT be used with this utility.


If you have a restricted network, you must first make sure that all sites listed below are enabled to be able to successfully use microPOD Setup Utility and the wiTECH 2.0 System.

Note: Please disable any Anti-Virus software that you have on your computer in order to allow the microPOD Setup Utility to install and run properly.

How to download and install the microPOD Setup Utility

IMPORTANT: Once the microPOD is configured using the  auto scanner diagnostic tool microPOD Setup Utility, all the microPOD Wireless Settings will be deleted. You will be required to follow the instructions from the KB link titled “How to configure a Wireless Profile on a microPOD II”.

To download the application, please login to DealerCONNECT > Service > wiTECH Information > microPod Setup Utility

Step 1

Click on “Run” to begin the downloading process of microPOD Setup Utility.


Step 2

The install wizard will appear to install the wiTECH Driver x64 onto your computer if your PC has not been installed with wiTECH 1.0 application.

If the PC has been installed with wiTECH 1.0 App, you will not see the screen below and proceed to Step 6. Otherwise, click “Next” to proceed.


Step 3

Read the License Agreement carefully, and accept the terms in the license agreement. Then, click “Next” to continue.


Step 4

You are now ready to start the actual installation of the driver. You now need to click on “Install” for it to start.


Step 5

This will now install the wiTECH Driver x64. Once complete, the program will automatically proceed to the next step.


Step 6

Once the installation has completed, click “Finish”. Proceed to the following section, “Using the microPOD Setup Utility”.

Using the microPOD Setup Utility

NOTE: Please make sure that your computer is connected to the internet and the microPOD is connected to the computer via USB before starting this process. This application will help you configure your microPOD for wiTECH 2.0 from

Step 1

Start microPOD Setup Utility by clicking the icon on the desktop:


If the microPOD Setup Utility that is installed is out of date, you will be forced to update to the newer version of the application.

Step 2

Please make sure your microPOD is connected to the PC via USB.


Step 2a

If you see the following screen you may not be connected to the internet, or have a firewall that blocks 1 or more of these websites.


Select “Continue” on the next screen for wiTECH 2.0 Device Setup and Configuration.


NOTE: If you only want to configure the wireless setting on a microPod device to use with wiTECH 2.0, click “Wireless Configuration” and follow instructions.

Select “Continue” on the next screen to begin attempting to connect to the microPOD device.


Step 3

Once your microPOD II is recognized by the utility, select “Continue” to proceed with the configuration.


NOTE: microPODs with a serial number beginning with “WFP” should NOT be used with this utility.

Step 3a

If the utility does not find the microPOD device, please assure that the microPOD is connected via USB and click “Refresh”


Step 4

The following screen will appear for up to 15 minutes while the microPOD device is being configured.


Step 5

The following screen will appear when the utility completed the configuration of microPOD for wiTECH 2.0 Application.

Note: After microPOD Setup Utility is ran, all existing wireless networks will be removed from the microPOD.

Important! Leave the microPod Setup Utility window running as you will be required to complete software updates to the microPod device before configuring the wireless.

Step 5a

Login into wiTECH 2.0. The microPOD II that was just configured using the microPOD Setup Utility should appear in the wiTECH 2.0 discovery. You will need to update the operating system of your microPOD II before it can be used with Micropod 2 Chrysler MicroPOD II. Click “Continue”, and your web browser will redirect you to the page to download and install the operating system update as seen in the following step.


*NOTE: If microPOD II does not show up in discovery after a couple of minutes please power cycle your microPOD II by unplugging it and plugging it back in.

Step 6

Click “Update Now” and your microPOD II should continue to the update screen. Once updating, do not interrupt your microPOD II at any point until the update is complete.


*NOTE: This can take upwards of 9 minutes. It is normal activity for the microPOD II to reboot.


Step 7

Click “OK” and you will be navigated back to the wiTECH 2.0 discovery page. Your microPOD II should appear updated and ready for use.



Step 8

With the microPod Setup Utility still running, configure wireless on the wiTECH microPod II device.


V17.04.27 Chrysler VCI Pod Micropod 2 wiTECH Software Free Download

Chrysler Micropod 2 wiTECH v17.04.27 Software Free Download
V17.04.27 Chrysler wiTech MicroPod 2 Chrysler Micropod VCI original software released. Chrysler Witech Micropod 2 with V17.04.27 witech 2.0 Dealer connect software support Chrysler till 2017. Witech Micropod 2 also cover Dodge, Jeep, and Fiat vehicle diagnostics. Below share wiTECH v17.04.27 Chrysler micropod 2 original software free download link and installation guide here.

WiTech Micropod ii Chrysler VCI Pod 2 Diagnostic/Programming Tool

witech micropod 2 V17.04.27 Chrysler VCI Pod Professional Diagnostic Tools Micropod 2 wiTECH Software

It’s wiTECH software crack
No need password for wiTECH MicroPod 2 login
No need wiTECH software license
Tested OK by professionals
Safe to use with wiTECH MicroPod 2 clone
Operation system of wiTECH 2 download: Windowns XP/7 wiTECH Micropod 2 v17.04.27 software Installation Tips:
1.The date of the computer must be the current time
2.The computer must be connected to the Internet
3.Connect the machine to the MicroPod 2 to open the wiTECH software
4.The system may ask you to turn off the software and turn it on for registration again.
5.Repeat it for several times.
Then you can use it normally

wiTECH MicroPod Kit 2 v17.04.27 Software Crack Install Guide:
Step 1 install AdobeAIRInstaller.exe
Step 2 install jre-6u45-windows-i586.exe
Step 3 install wiTECH_Install_17.04.27.exe
Step 4 Restart the computer
Finish Installation

Witech Software for Chrysler Micropod 2 Display: