Porsche Coding using PIWIS Development Mode

Piwis 3
CnAutotool.com here provides some coding procedures using Porsche Tester Piwis III

To code you need to be in development (E) mode, which is unfortunately in German. I’ve made a start at doing some translations courtesy of Google Translate below.

If you play around in simulation mode, the car it uses is a 991 coupe. Whilst not exactly the same as the 981, it’s very close. It’s a good start at poking around the software to see where things are without having to be connected to the car.

Some general phrases

Codierung Anpassungen
Coding adaptations

Keine Eintrage gesetzt
No value set

Codierwert or kodierwert
Coding value

Wert
Value

Verbaut
Installed

Geandert
Changed

aktiv
Active

Inaktiv
Inactive

Einheit
Unit

Geandert
Changed

Schreiben
Save

Ja
Yes

Nein
No

MCR = Machine-readable Coding Rules

Manuelle Codierung ohne MCR Regeln (Entwicklung)
Manual coding without MCR rules (development)

Manuelle Codierung von Binärdaten (Entwicklung)
Manual coding of binary data (development)

Manuelle Codierung mit MCR Regeln
Manual coding with MCR rules

Automatische codierung
Automatic coding

Rucksetzen auf werkeinstellungen
Reset to factory settings

geben sie bitte fahrzeugdaten ein
Please enter vehicle data

werte andern und mit speichern
change values and save with

weiter zum nachsten screenmit
continue to the next screen with

coderung lauft
coding is running

codierung von steuergeräten
coding of control units

Control Module names

waehlebel
Gear selector lever

kombiinstrument
instrument cluster

kombilenkstockschaltermodul
steering wheel module

stoppuhr
stopwatch

audio verstärker
audio amplifier

bedien und klimaeinheit
operation and climate

parkbremse
park brake

reifendruckkontrolle
tyre pressure control

dämpfersteuerung
damper control

servolenkung
power steering

verdeck synchronisation
convertible top

BCM vorne
Front Body Control Module

BCM hinten
Rear Body Control Module

scheinwerfer links
Left headlight

scheinwerfer rechts
Right headlight

spurwechselassistent
lane change assistant

sitz fahre
driver seat

sitz beifahrer
passenger seat

tuer vorne links
left front door

tuer vorne rechts
right front door

soundaktuator innen
inside sound actuator

DME coding translations

Manual coding without MCR

Bestelltyp
ordered type

getriebetyp
transmission type

innenausstattung
interior decoration

kodierung kodierbyte
coding coding byte

tempomat
cruise control

start/stopp aktiv
start stop active

allradantrieb
all wheel drive

abgasklappen
exhaust flap

getriebedrehzahlsensor
transmission speed sensor

kraftstoff brasilien
fuel brazil??

Gerauschtypisierung Asien
Noise typing Asia

Tankleckdiagnose Feinstleck
Tank leak diagnosis

Kraftstoffmarkt
Fuel market

Kodierung gultig
Coding valid

Landercode
Country code

Nummern
Numbers

Ruckrufaktion
Product recall

Seriennummer Wegfahrsperre
Serial number immobilizer

Tester Produktionsmodul
Tester production module

Verbauvorschrift
Building regulations

Wagen und Verdeckfarbe
Car and top color

Wartungsdienste
Maintenance services

Manual coding with MCR

Landercode
Country code

Modelljahr
Model year

Produktschlussel
Product key

Bordcomputer
On board computer

Anzeigendonfiguration
Show configuration

schlussel
Key

fahrzustand
driving state

 

Last Mode coding DIY

This is a Porsche PIWIS III DIY to recode the car so that it keeps the last driving modes set. I used this primarily to ensure that start/stop initialises OFF each time I start the car rather than me having to push the button each time I start the car.

I don’t know what other modes it keeps for the next time your start the car. It seems to keep the last PASM and seat heating settings, but not SPORT or SPORT PLUS.

Note: Development mode is in German. English translations are after each step to show what you are doing.

I can’t take credit for the procedure. I won’t name who it was, but they know who they are, and thanks for the help.

If you are worried about doing this for the first time on your car, it’s the same in simulation mode, so have a practice here first. Being simulation mode, it won’t let you save it.

To make the coding changes, do the following.

Change the PIWIS mode to E (development)

Open the diagnostics for the car type, then make the following selections.

1. BKE (bedien und klimaeinheit)
operation and climate

2. Codierung Anpassungen
Coding adaptations

3. Manuelle Codierung ohne MCR Regeln (Entwicklung)
Manual coding without MCR rules (development)

4. Select both kodierwert:kodierwert default fahrzustand and kodierwert:kodierwert default fahrzustand last mode
codeword default driving state

5. In Wert (value) dropdown
Change …fahrzustand to “last mode”
Change …fahrzustand last mode to “ja”

6. Click schreiben (save) at bottom.

Coding complete. Exit and change the settings back to V (aftersales) mode if desired.