Upgrade Process for K518 Adaptor Kernel

After the APK of Lonsdor K518S Key Programmer is upgraded to V1.6.0 version, the adaptor requires to be installed new kernel beforehand. Please refer to below operations.

Step 1: Connect the device to the specified adaptor and plug in 12V power, as shown below.

01-01

Step 2 : Start up the device, and input password to enter home screen. Click “Update firmware” button in below red box.

01-1

Step 3: The following interface appears, click “Install Adaptor” in below red box.

01-2

Step 4: It skips to the below interface, click “OK” to continue.

01-3

Step 5: It skips to below interface. You will see the progress indicator moving rightwards. When downloading is completed, click OK” and exit. The adaptor kernel is installed successfully.

01-4

Porsche-Cayenne-Help File

Basically, there will be 4 parts in the whole help file: Function, Reference, Attention and Operation.

Function

1. Program smart key: to program smart card (please make dealer key first);

2. Make dealer key: use the backed up BIN data to make the non-dedicated key to be dealer key.

Reference

Chip type: Dedicated smart card

Frequency: 315/433/434 frequency (please check the logo in the lower right of the lid of the BCM box)

Key embryo no.: 31

Code requirement:Dismantle & read BCM to make dealer key

Key generation: Program smart key complete, remote will automatically generated

Under the steering wheel (BCM position):

Porsche-Cayenne-Help- File-1
BCM is located at the bottom left of the steering wheel, please note the frequency type, basically there will be 315/433/434,

The following picture is for 434 frequency:
Porsche-Cayenne-Help- File-2

11-15 Cayenne Car Model

Porsche-Cayenne-Help- File-3

The car key

Porsche-Cayenne-Help- File-4

The induction keyhole

Porsche-Cayenne-Help- File-5

The mechanical knob key inserted into the induction keyhole

Porsche-Cayenne-Help- File-6

Attention

1. All the keys need to learn, or it will not be able to start the vehicle, it is recommended to learn the original car keys first,and then learn the new key, battery must be well installed.

2. The newly added key must be either the dealer key made via the car BCM data, or the key ordered back through the VIN code.

3. When learning key, it is required to insert the key into the induction keyhole, to learn a smart key, remove the machanical rotate key from the induction keyhole if any and then insert the smart key to program.

Operation

Step 1: Use the Lonsdor K518S to read and write BCM data and save it as bin file;

1. BCM is located in the lower left of the steering wheel, please pay attention to view the frequency type, usually there will be 315,433,434 frequency (below picture is for 434):

Porsche-Cayenne-Help- File-7

2. Read the BIN (D-FLASH / EEPROM) file with the programmer specifically for reading BCM. Please pay attention to the type here: namely 1L15Y 2M25J metal crystal, or 5M48H 1N35H ceramic crystal (red mark):

Porsche-Cayenne-Help- File-8

3. Please refer to the following picture to wire:
Porsche-Cayenne-Help- File-9

Porsche-Cayenne-Help- File-10

Step 2: Copy the bin file into Auto key Programmer K518ISE: please use the USB cable to connect the K518ISE to the computer, open the device internal memory, find the folder “customfile” and copy the bin file into it (as shows below).

Note: bin file suffix “bin” must be lower case letters, directly put the file into the folder rather than create a new folder:
Porsche-Cayenne-Help- File-11

Step 3: Make dealer key

Step 4: Program smart key

Lonsdor K518 reads PIN for older Fiat 2005-2012: Confirmed!

Question for Lonsdor K518S:

When You are planning to add PIN read for older Fiat ??

(Doblo 2005 – 2009 or Ducato 2006 – 2012 etc. )

Answer by CnAutotool.com:

Easy.

The steps:

Read dump with FVDI

Then VVDI-Prog can calculate PIN from dump

(Tango doesn’t show pin, and you need pin for remote programming)

Then continue with Lonsdor – Immo learn + remote

The test on Doblo:

lonsdor-k518ise-older-fiat-read-pin-1

Select a model:

Fiat- Europe-Doblo-2009-
lonsdor-k518ise-older-fiat-read-pin-2 lonsdor-k518ise-older-fiat-read-pin-3 lonsdor-k518ise-older-fiat-read-pin-4 lonsdor-k518ise-older-fiat-read-pin-5

Lonsdor reads PIN codes

lonsdor-k518ise-older-fiat-read-pin-6

The function can read PIN code and save data

lonsdor-k518ise-older-fiat-read-pin-7

Pls use a working key to turn ignition ON

For a smart key, pls put it close to induction coil

lonsdor-k518ise-older-fiat-read-pin-8

Open the ignition switch

lonsdor-k518ise-older-fiat-read-pin-9

K518 manages to read PIN codes

PIN is saved

Pls use [program key] function to program a key
lonsdor-k518ise-older-fiat-read-pin-10

Done!