How does Galletto v54 read in bootmode on EDC15P ECU’s?

This is a quick guide on how to use Galletto v54 to read in bootmode on EDC15P ECU’s. I hope some of you can use this too, as there are only guides for this with MPPS.
It appears however, that it’s not possible to write the ECU in bootmode using this feature. I have at least not had any luck with it. Feel free to correct me if I’m wrong.
Credits to @ nps1994 (DK member)

Step 1: Open the ECU.
I did this carefully with a screwdriver.

Step 2: Locate the 29f400 chip.
This is where the flash is stored.

Step 3: Fire up ECU Programmer FGtech and go to Tools Boot Mode > Siemens-Infineon C167 > Bosch ME7 – 1 Micro – Flash 400 Boot Mode.

Step 4: Connect the ECU like this without putting on power yet (On my pictures I have made an EDC15 to OBD adapter, but basically the same):

boot-reading-of-edc15-with-galletto-v54-01

Step 5: Press Read ECU now follow the instructions (Put ground on pin 24 of the flash > Apply power > Remove ground after approx. 5 seconds)

All gone well Galletto 4 should now read the flash.

I have attached some pictures for more detailed instruction.
Hope this can help somebody!
boot-reading-of-edc15-with-galletto-v54-02 boot-reading-of-edc15-with-galletto-v54-03 boot-reading-of-edc15-with-galletto-v54-04

Thanks

Free download witech 2 v17.04.27 for micropod 2 Chrysler diagnostic tool

Tested more stable than witech 2 v17.04.27

Compatible with HQ China witech micropd 2 and original one

windows 7 32bit or 64bit

Diagnosis: Confirmed

Programming online/offline: Confirmed

Multi-languages: English, French, Spanish, German, Italian, Russian, Japanese, Korean and Chinese

Workable cars: Chrysler, Jeep, Dodge, Fiat

witech 2 v17.04.27 win7 installation:

*** Do not connect to network when you use the device.
First connect MicroPodII to vehicle, if the red indicator turns on, then connect to laptop and run software.

Read this article: how-to solve wiTECH MicroPod 2 with serial xxxx not registered?

DRBIII Emulator if possible?

witech micropd 2: DRB III emulator confirmed working, but it doesn’t contain DRB III emulator in the package, you have to buy your own separately.

Besides, WITECH VCI POD comes with DRBIII Emulator, works offline and more stable

There are free source of DRB III Emulator on Mega:

*** Please use the free source at your own risk, no one will take responsibilities for any risk.

I managed to make the Enhanced DRB III Emulator work with a micropod clone on V17.04.27 Witech with Windows 7 32 bits all offline mode and no subscription.

First install Witech then install the Professional Diagnostic Tool DRB emulator and then the enhanced one.

find it here : C:\ProgramData\wiTECH\jserver\data\core\stubs

Or use the files from here:

Afterwards plug usb in pod then pod in the car turn ignition to on position and at last in the laptop

Open web browser, i used firefox and in the address bar put this and press enter :
It will launch the enhanced emulator.

Read this article: what is Enhanced DRB III Emulator and how to install?

How to tell a good quality witech clone?

-> working exactly like an OEM unit.

-> No errors and tested functions on different vehicles.

-> confirmed working with unmodified software wiTECH v17.03.10 (downloaded directly from Chrysler) and online (logged into TechAuthority).

-> used it on a 2014 dodge avenger just fine.

-> was able to flash a module update and program a new key with the unit.

-> uploaded pictures of the internals for those who are curious.
micropod-2-witech-pcb-1

micropod-2-witech-pcb-2

micropod-2-witech-pcb-3

micropod-2-witech-pcb-4

And this HQ MicroPod 2 outlook

micropod-2-witech-pcb-5

micropod-2-witech-pcb-6
Thanks.

Xtool EZ400 Pro Read Fault&Erase Fault on Mercedes W205

Xtool EZ400 Pro Read Fault&Erase Fault on Mercedes W205

But how to use it to get ?

Here is the steps to show how to do

1.Connect Mercedes W205 with Tablet

2.Enter Benz Models

Click” Automatic Vehicle Identification” to check Vehicle Information

Once confirming the information is correct,click Ok to continue

Enter Gasoline Engine

And then Click “Quick Test”

Enter Diangosis Menu

And repeat the process erase fault code till erase successfully

for more informations,please click following link

XTOOL X100 PAD2 Program Proximity/Fobik for Dodge Dart 2013

This article show test on how to use Xtool X100 Pad2 to program new keys for Dodge Dart 2013.

XTOOL - X100 - PAD2 - Program - 1

Procedures:

Connect XTOOL X100 PAD2 programmer to Dodge Dart

Enter the menu to select IMMO function

Select “Chrysler/Jeep/Dodge”

Select “Proximity/Fobik”

XTOOL - X100 - PAD2 - Program - 2

Dodge

XTOOL - X100 - PAD2 - Program - 3

Dart 13

XTOOL - X100 - PAD2 - Program - 4
It will prompt you to turn Hazards On or turn Ignition off

XTOOL - X100 - PAD2 - Program - 5

Program Keys

XTOOL - X100 - PAD2 - Program - 6

Place a new Fobik into the ignition.

Ignition switch must be in the “Lock” or “Off” postion

Press “OK” to continue

XTOOL - X100 - PAD2 - Program - 7

Please enter security code,after entering security press “OK” to continue

XTOOL - X100 - PAD2 - Program - 8

Programming success.

XTOOL - X100 - PAD2 - Program - 9

Now test the new key on your Dodge Dart 2013.

EEPROM Adapter Use Guide: Read Pin Code, Initialize Data, Read-Write Chip

EEPROM which developed by XTOOL is a tool which could use to read chip that needs to be removed when reading IMMO pin code. User could remove the chip from Immobiliser or dashboard and then read pin code via EEPROM.

XTOOL EEPROM Adapter is designed for X100 PRO /X200S /X300 Plus/X100 PAD

Chip socket has 3 chip types: 3XXX, 25 (95) XXX and 24XXX

Read - Write - Chip - 1

How to connect EEPROM with chip and X100 PRO /X200S /X300 PLUS:

Read - Write - Chip - 2

The following will share the EEPROM function like reading pin code, initialization data and read- write chip.

Take Changan CX20 for example to show how to read IMMO pin code:

Take apart the EEPROM chip from the vehicle control unit.
Find the correct chip socket according to chip type (pay attention: both directions of chip and chip socket should be the same, otherwise password will fail to be read).
Connect EEPROM chip with XTOOL X100 PRO or XTOOL X300 PLUS.
Choose “EEPROM Adapter” and “Read Pin Code” function.

Read - Write - Chip - 3

Select car model “Changan”->”C20”

Read - Write - Chip - 4

Choose ECU type ”ECU(93C46)’

Read - Write - Chip - 5

And the pin code of Changan C30 could be read out

Read - Write - Chip - 6

Next, share the guide to initialize data by taking Toyota for example.

Choose “initialize data”-> car model “Toyota”

Read - Write - Chip - 7

Chose the initialization type “Smart system initialization”

Read - Write - Chip - 8

Then select the detail car model “HIGHLANDER”

Read - Write - Chip - 9
Choose the initialization type, pay attention to Immobiliser and ECU type.

Read - Write - Chip - 10

Save the file and the xtool will remind you to initialize. Choose yes and initialization will be done.

Read - Write - Chip - 11

How EEPROM read-write chip

Before reading or writing chip, please remove the chip from car and connect it with chip holer

Choose ”EEPROM chip read/write” function
Read - Write - Chip - 12

Choose the right chip type

Read - Write - Chip - 13

Select the file name to save

Read - Write - Chip - 14
Choose the file to recover.
Read - Write - Chip - 15

After confirming the right file, the chip is successful read and write.

Read - Write - Chip - 16

If you buy xtool x100 pro on CnAutotool, you could get one EEPROM adapter with your package.

XTOOL Tablet Series update for Toyota, BMW, Nissan

XTOOL pad series updated recently, this update includes Toyota, BMW, Nissan. Updated Toyota V11.60 add new European models and modify. For BMW V10.30, added BMW and HCBMW E chassis programming and coding function. And updated Nissan V10.81 add new supported functions based on ECU and fix some problem.

TOYOTA - V11 - 60

================TOYOTA V11.60========================

Language version of the vehicle system software is currently released for English、Spanish、Portuguese、Polski

Update:

Add European models such as NX200, C-HR, HARRIER, CAMRY HV, LS350, HIGHLANDER/KLUGER, INNOVA/KIJANG INNOVA, COROLLA/AURIS, etc.
Add and modify more than 500 route menus in Europe.
Modify the problem that 2017_Corolla HV Central Gateway DataStream does not support.
Modify 2003_ CAMRY cruise, Immobiliser DataStream is not supported.
Modify the 2017_Corolla meter data stream, the “HVAC System Indicator” value shows an incorrect question.
Modify the 2005_Vios engine DataStream missing issue.
Modify 2014_Pruis Transmission DataStream multiple display problem

================BMW V10.30========================

Language version of the vehicle system software is currently released for English, Spanish, Polski, Portuguese

Update:

Added BMW and HCBMW E chassis programming and coding function(Please update APP before use);
Optimize automatic diagnosis;
Optimize data stream and action testing;
Optimize service function.

=================NISSAN V10.81========================

Language version of the vehicle system software is currently released for English、Spanish、Polski、Portuguese

Update:

1. Add some new ECU based support function of the system.

2. Optimize menu for TIIDA in China.

3. Solve some abnormalities in special functions and motion tests such as the 2003 ALTIMA, 2017 QASHQAI, 2011 INFINITI EX25, 2016 PULSAR, and 2015 TEANA vehicle.

Note: This XTOOL Pad series update contains  XTool X100 PAD, X100 Pad2, XTOOL EZ500, EZ400, EZ400 PROXTool PS2 etc…

XTOOL EZ400 Diagnose 2010 BMW 730Li Process

Xtool EZ400 Pro is a new style vehicle diagnostic tool released by XTOOL. Here is the process how XTOOL EZ400 Pro diagnose BMW 730Li 2010.

Diagnostic tool: XTOOL EZ400 PRO

Car Model: 2010 BMW 730Li

After connecting the EZ400 Pro with BMW, tap “BMW” and choose “Automatic selection” to let the EZ400 Pro tablet to check the detail of the vehicle.

xtool-ez400-pro-diagnose-BMW-1

Confirm vehicle profile and tap Yes.

xtool-ez400-pro-diagnose-BMW-2

Tap Diagnosis -> Auto Diagnosis and the tablet will diagnose automatically.

After it finishes scanning, choose CAS Car access system and tap Diagnosis, then the function menu will show up with identification, read fault memory, clear fault memory, live data and component activation.

Note: the function menu will be different in different car models.

xtool-ez400-pro-diagnose-BMW-3 xtool-ez400-pro-diagnose-BMW-4

Here will show you the function one by one. Take CAS Car access system diagnosis for example.

Identification

xtool-ez400-pro-diagnose-BMW-5

Read fault memory

xtool-ez400-pro-diagnose-BMW-6

Clear fault memory

xtool-ez400-pro-diagnose-BMW-7

Live data

xtool-ez400-pro-diagnose-BMW-8

www.cnautotool.com

Update! XTOOL Pad Series Update in HYUNDAI V11.70

XTOOL -UPDATE- - -1

Xtool Pad Series update for Hyundai!

This update adds some new car models in base function of reading and clear code, data stream and action test and ecu version. Go ahead to view details:

Note: This XOOL Pad series contains Xtool Pad, X100 Pad2, XTOOL EZ500,EZ400,EZ400 PRO etc…

Update:
Add HYUNDAI(USA area) Accent in 2016 and 2015

Azera in 2016 and 2015

Elantra in 2017 to 2015

Equus in 2016

Genesis in 2016

Santafe in 2017 to 2015

Sonata in 2016

Tucson in 2016 and 2015

Veloster in 2016

base function of reading and clear code, data stream and action test and ecu version.

2002 Audi TT Throttle Body Adaptation Succeed with Xtool VAG401

This post intends to show you how to use VAG401 to do Throttle Body Adaptation on a  2002 Audi TT.

Jump into “Diagnosis systems”.

throttle-body-adaptation-with-xtool-vag401-1

Common system.

throttle-body-adaptation-with-xtool-vag401-2

Engine

throttle-body-adaptation-with-xtool-vag401-3

Xtool VAG401 is connecting to the engine of 2002 Audi TT.

throttle-body-adaptation-with-xtool-vag401-4

Reading system information…

throttle-body-adaptation-with-xtool-vag401-5 throttle-body-adaptation-with-xtool-vag401-6

Checking the code read itself.

throttle-body-adaptation-with-xtool-vag401-7

Data block Measurement

throttle-body-adaptation-with-xtool-vag401-8

Input Channel Number (0-255

throttle-body-adaptation-with-xtool-vag401-9 throttle-body-adaptation-with-xtool-vag401-10

9.Basic settings.

throttle-body-adaptation-with-xtool-vag401-11

Electronic Throttle, you can see the adaptation is running, the sensor reading is changing…

throttle-body-adaptation-with-xtool-vag401-12

Thanks for reading.