How to Set up wiTech MicroPod 2 Chrysler Diagnostic Tool

This is a how-to guide of wiTECH MicroPod 2 Chrysler diagnostic tool setup.

If your dealership purchased a new microPOD and you would like to convert your existing microPOD for using with wiTECH 2.0 System, you need to download and install the microPOD Setup Utility to configure/setup your microPOD for wiTECH 2.0.

NOTE: microPODs with a serial number beginning with “WFP” should NOT be used with this utility.


If you have a restricted network, you must first make sure that all sites listed below are enabled to be able to successfully use microPOD Setup Utility and the wiTECH 2.0 System.

Note: Please disable any Anti-Virus software that you have on your computer in order to allow the microPOD Setup Utility to install and run properly.

How to download and install the microPOD Setup Utility

IMPORTANT: Once the microPOD is configured using the  auto scanner diagnostic tool microPOD Setup Utility, all the microPOD Wireless Settings will be deleted. You will be required to follow the instructions from the KB link titled “How to configure a Wireless Profile on a microPOD II”.

To download the application, please login to DealerCONNECT > Service > wiTECH Information > microPod Setup Utility

Step 1

Click on “Run” to begin the downloading process of microPOD Setup Utility.


Step 2

The install wizard will appear to install the wiTECH Driver x64 onto your computer if your PC has not been installed with wiTECH 1.0 application.

If the PC has been installed with wiTECH 1.0 App, you will not see the screen below and proceed to Step 6. Otherwise, click “Next” to proceed.


Step 3

Read the License Agreement carefully, and accept the terms in the license agreement. Then, click “Next” to continue.


Step 4

You are now ready to start the actual installation of the driver. You now need to click on “Install” for it to start.


Step 5

This will now install the wiTECH Driver x64. Once complete, the program will automatically proceed to the next step.


Step 6

Once the installation has completed, click “Finish”. Proceed to the following section, “Using the microPOD Setup Utility”.

Using the microPOD Setup Utility

NOTE: Please make sure that your computer is connected to the internet and the microPOD is connected to the computer via USB before starting this process. This application will help you configure your microPOD for wiTECH 2.0 from

Step 1

Start microPOD Setup Utility by clicking the icon on the desktop:


If the microPOD Setup Utility that is installed is out of date, you will be forced to update to the newer version of the application.

Step 2

Please make sure your microPOD is connected to the PC via USB.


Step 2a

If you see the following screen you may not be connected to the internet, or have a firewall that blocks 1 or more of these websites.


Select “Continue” on the next screen for wiTECH 2.0 Device Setup and Configuration.


NOTE: If you only want to configure the wireless setting on a microPod device to use with wiTECH 2.0, click “Wireless Configuration” and follow instructions.

Select “Continue” on the next screen to begin attempting to connect to the microPOD device.


Step 3

Once your microPOD II is recognized by the utility, select “Continue” to proceed with the configuration.


NOTE: microPODs with a serial number beginning with “WFP” should NOT be used with this utility.

Step 3a

If the utility does not find the microPOD device, please assure that the microPOD is connected via USB and click “Refresh”


Step 4

The following screen will appear for up to 15 minutes while the microPOD device is being configured.


Step 5

The following screen will appear when the utility completed the configuration of microPOD for wiTECH 2.0 Application.

Note: After microPOD Setup Utility is ran, all existing wireless networks will be removed from the microPOD.

Important! Leave the microPod Setup Utility window running as you will be required to complete software updates to the microPod device before configuring the wireless.

Step 5a

Login into wiTECH 2.0. The microPOD II that was just configured using the microPOD Setup Utility should appear in the wiTECH 2.0 discovery. You will need to update the operating system of your microPOD II before it can be used with Micropod 2 Chrysler MicroPOD II. Click “Continue”, and your web browser will redirect you to the page to download and install the operating system update as seen in the following step.


*NOTE: If microPOD II does not show up in discovery after a couple of minutes please power cycle your microPOD II by unplugging it and plugging it back in.

Step 6

Click “Update Now” and your microPOD II should continue to the update screen. Once updating, do not interrupt your microPOD II at any point until the update is complete.


*NOTE: This can take upwards of 9 minutes. It is normal activity for the microPOD II to reboot.


Step 7

Click “OK” and you will be navigated back to the wiTECH 2.0 discovery page. Your microPOD II should appear updated and ready for use.



Step 8

With the microPod Setup Utility still running, configure wireless on the wiTECH microPod II device.


MaxiTPMS TS608


As the first comprehensive TPMS & Diagnostic tool in the market, Autel MaxiTPMS TS608 provides you with superior experience in TPMS health check, sensor programming, TPMS relearn, all system diagnostics as well as special service functions. Equipped with a 7-inch touch screen with 1024 * 600P resolution and a VCI mini for wireless communication with the test vehicle, powered by the quad-core Cortex-A9 processor for smooth operation and featured by advanced TPMS & Diagnostic technology, MaxiTPMS TS608 is setting new standards for TPMS service tools.


The latest compact size Autel Scan Tool Wireless Bluetooth MaxiVCI Mini OBDII connector can transmit vehicle data to the tablet without a physical connection. Enhanced wireless bluetooth connectivity between the tablet and VCI device allows greater service mobility and easier TPMS sensor interaction while the tablet is still connected to the vehicle for data transmission.


1.Activate all known TPMS sensors and read sensor status

2.Diagnose ECU for complete TPMS health check with DTC description

3.Read DTCs from ECU and erase DTCs

4.Program MX-Sensors by copying original sensor IDs or creating new IDs randomly

5.On-tool relearn procedure and wide OBD relearn coverage

6.Toolkit, special TPMS functions


1.Read/clear codes for all available electronic systems

2.Turn off warning lights

3.Display live data in text, graph & analog for easy data review

4.Supports all 10 test modes of the latest J1979 OBD II test specs

5.Enhanced OBDII Mode 6


1.Relearn parking brake pad after replacement

2.Reset Steering Angle Sensor (SAS)

3.Reset service mileage and service intervals

4.Forced regeneration and adjusting injectors

5.Support battery registration and reset

6.Support IMMO functions




● All-in-one TPMS Solution
● Advance TPMS diagnostics with DTC description
● TPMS status, one step for complete TPMS health check
● Activate 98% of all known TPMS sensors
● Program Autel MX-Sensors
● Comprehensive OBD relearn coverage
● On-screen relearn procedure
● Toolkit, special TPMS functions
● Read/Clear codes for all available systems
● Display live data in text, graph & analog for easy data review
● Reset service mileage and service intervals
● Auto VIN technology can automatically identify the vehicle’s make, model and year information in no time
● Forced registration and adjusting injectors
● Relearn parking brake pad after replacement
● Support IMMO functions
● Reset Steering Angle Sensor (SAS)
● Support Battery registration and reset


● QTY – 11 – 315MHz TPMS sensors
● QTY – 11 – 433MHz TPMS sensors
● 2 TPMS Inventory Dispensors
● 2 year warranty on sensors


Why I got Autel Maxidas DS808 full kit

I have the first generation Autel MaxiDAS DS708 for many years, I love it because of its reasonable price and cost efficient function, but what a pity that it will not be updated any more.

Then you consider to have one MaxiDAS DS808K full kit which adds extra special functions i.e injector coding, key coding, adaptation, ECU information, trouble codes, freeze frame, live data, active test and special functions. I have one small repair shop and have many different car brands fix, DS808 can fully meet my requirements.

It has many different vehicles’ diagnostic adapters which are not standard 16pin(see following pic). Maxidas DS808 is compatible to many US, European, Asian vehicles, user friendly and has software for different vehicle models and systems.

13-1 13-2

Its new CPU and LCD touch screen (7″ LCD 1024×600 resolution touch scrren), dramatically improved the entire users’experience, much more smooth comparing with DS708. Personally, I would recommend DS808 for those small shops with limit budgets. Of course, if money is not a problem, Maxisys Elite may be your good choice.It is smaller than MS906, so very handy.

This is what I got Autel Maxidas DS808 full kit claims they are the exclusive sales dealer authorized by auteltech. Means lowest price $845 free shipping.

BTW, I am not affiliate with this shop, but a customer.

How to repair BMW 328xi E90 window regulator by Autel MS908P

The story is that: a 2006 BMW 328xi E90 rear right window was not working, replaced window regulator but it was stuck not all the way up and down. Used Autel MS908P to repair window regulator OK! So share this success case here.


How Autel MS908P initialize BMW window regulator, reset BMW auto window?

Plug the J2534 ECU Programming Device into car OBD port. Then you can use it to connect Autel Tool  MaxiSys Pro MS908P with car via Wi-Fi.

8-4 8-3

Click “Diagnostics” and choose “BMW”.

8-4 8-5

Or you can directly click the VIN button at left upper corner, choose “Auto detect” and it will read VIN automatically and show vehicle information.

8-6 8-7

Now you need to connect car with power charger over 12V. Then put remote key into key slot and press car Start button.


Then go to “Hot Function”.


Choose “Window, door and roof” then “Initialize window regulators” function.

8-10 8-11

Follow the tips “Switch on terminal 15 (ignition)”, keep remote key in key slot and do not press the brake pedal, press car Start button to turn ignition to terminal 15.

Choose to initialize the “Passenger’s side, rear” window regulator.


The rear right window will automatically open and close.

After that you can roll up and down that window normally.

Autel MaxiSys MS908P successfully initialize BMW 328xi E90 On rear right window regulator! BMW auto window reset OK!

AK500 Pro VS AK500+

AK500 Pro2 is the most advanced benz key programmer in the world as we mentioned before. And AK500 Pro is the only machine in the world that has KEY-LESS go writing function.

AK500+ is also an popular benz Key Programmer, it supports most Benz before year 2009, and it is much cheaper than AK500 PRO.


How To Use Piwis Tester II to coding Cayenne 92A MY 2011

Piwis Tester ii diagnostic & programming tool for Porsche, we know more about piwis tester 2 diagnostic functions. Do not know more about the coding function about Piwis Tester for Porsche.

Below share how to coding Cayenne 92A from MY 2011 rear-end electronics by Porsche piwis tester ii step by step.

Supplier Porsche Diagnostic Tool Piwis Tester 2 with Panasonic CF30 Tablet Full set Ready to Use

Tools to use step-by-step instruction:

1.Open Porsche PIWIS Tester 2 software, select “Diagnostics” – “Cayenne” – “92A from MY 2011” ,
staring up Porsche PIWIS Tester 2

2.Come to “Control unit selection”, select “Rear-end electronics”

3.Click F12 [Next] at the right corner.

Get message reading “Control unit search has been completed”. Select control unit(s) and select
the required function via the menu.

4.Click “Fault memory” and clear ALL or selected warning-event entries with [F8].

5.Click “Codings adaptations”, select coding mode [Automatic coding]. Press [F12] to continue.

6.Coding has been completed successfully. Press [F12] to continue.


Hope this airticle can help you learn more function about out  professional automotive diagnostic tool Porsche Piwis Tester 2.

Porsche Piwis 2 Porsche Cayenne 2010 Change Engine Control Unit Online Programming

Porsche piwis II from 100% work for online coding server, Porsche piwis II with V18.100 piwis 2 software available. Customer can order Porsche piwis II with Laptop installed Piwis 2 software ready to use for Porsche piwis 2 online coding. Below share Porsche piwis 2 Cayenne 2010 Change Engine Control Unit Online Coding Cases as following.

Porsche PIWIS 2 Online Programming Backgroud:

A customer from Cameroun need Porsche online programming for Porsche Cayenne 2010, the car have been changed a new engine model, so need Porsche online programming for new engine module adapting.

Below information from customer, which have show all Porsche PIWIS 2 online programming preparetion:

1. Porsche Piwis 2 Original Plan Device, 1:1 as Professional Diagnostic Tool Porsche Piwis 2 from

2. Porsche Piwis 2 software installed on laptop show the PIWIS 2 diagnostic result

3. Porsche Diagnostic Tool Porsche Cayenne 2010 VIN number and car informations

4. Order the One Time Porsche Online Programming Service from, and finish payment.

5. Then send us the Porsche online programming order number or transaction ID with car information.

6. Then we will help customer appointment for Porsche Piwis Online Programming. Kindly Note: make sure you have stable and fastest Network for Porsche PIWIS 2 Online Programming, otherwise it will take long time.

7. Car charger connected

8. Porsche Cayenne Key on, Network fast for Porsche online programming, then our technician will star Porsche piwis 2 online coding for you.

9. Then Send the teamviewer id and password to our sales once appointment time arrived

10. Pls beside the car when Porsche piwis 2 online programming doing,  sometimes need you corporation help for Porsche online coding.

11. Porsche piwis 2 online programming finished, check the car within half an hours and feedback to us, we will default this Porsche online programming service from be finished. Do not support refund any more. Porsche Piwis 2 Online Programming may finished within 1 hour( Under network good performance). It’s available for all Porsche Online Service application car.

Any need for Porsche Online Programming Service or Porsche piwis 2 with Porsche piwis 2 software installed on laptop for Porsche diagnostics just contact us freely.

Autel MaxiSys MS908P Cannot Communicate after Upgrade (Solved)

Autel MaxiSys MS908 or Autel MaxiSys MS908P automotive diagnostic scanner can not communicate and diagnose vehicles after upgrade problem solution provided.


One of the Autel MS908 scanner users has newly got the scan tool updated software he need to latest version, but the newly upgraded Maxisys system can not communicate/access to car.  So He decided to run an upgrade again.

But the device prompted it is the latest version. Then He tried to diagnose other models. He followed the system instruction to turn ignition switch to ON position, but the device still prompted turn ignition on and fail to communicate and diagnose any cars.

Possible reason:

Incorrect update procedure or did not upgrade software completely.


Note: The solution fits Autel Maxisys MS908 Pro from as well.

Un-install all upgraded software
Come to Autel MS908 diagnostic scanner main unit, select “Data Manager” function


3) Select “Apps”


4) Delete upgraded software


5) Download and update the vehicle software you need again, wait the procedure completed.


6) Re-connect the Autel Maxisys MS908P with vehicle and perform diagnosis.

3 steps to do MB SCN Coding Online easily by Autel MS908P

This blog will show you how to do Mercedes SCN coding in 3 steps by Autel MaxiSys Pro MS908P. As you know, Benz SCN Coding Service will charge about $150 one time, but with Maxisys MS908P you can do it at your fingertips!


Why we need to do SCN coding?

When replacing or flashing ME control unit or new Transmission control unit we must get new SCN, that is to say SCN coding.

How use Autel MS908P to do MB SCN coding in 3 steps?

Step1. You should first connect Autel MS908P to J2534 ECU programming device and Benz car. Next start Autel Scanner Autel MS908P and choose “Diagnostics”→ “Benz”→ “Automatic selection”


Then turn on ignition and wait a minute to read VIN. After read click “OK”.


Step2. Click “Programming” on main menu, next click “ME-SFI-Gasoline engine control”.

Click “Control module programming”→ “NEXT”→ “OK”→ “OK”.

13-8 13-9

Step3. Click “SCN coding”, you can see two steps.


Click “Step1”, soon you will see “Get SCN data from sever completed”. Then click “Step2”, wait a minute and you will see “Perform SCN coding completed”. Now you successfully use Autel MaxiSYS MS908 Pro to do Benz SCN coding in just 3 steps!

13-12 13-13 13-14

Of course,  Maxisys Pro MS908P Pro from CnAutotool not only can do SCN coding but also has many other functions like diagnostics, ECU coding and flash programming, J2534 Reprogramming, etc. It covers more than 40 US, Asian and European vehicle makes till 2017.