15 minutes SKP900 program Ford Explorer Keyless Remote OK

This blog will tell you 2 things:

1.It’s tested SKP900 Key Programmer can program Ford Explorer remote key fob within 15 minutes!
2.How? Any instructions and pictures to prove it?

Yes, check below!

Step 1

Power on SKP900 and connect it with car via Ford Explorer OBD2 port.

Choose “IMMOBILIZER”→ “FORD” → “EXPLORER KEYLESS 11”.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/18-1.jpg
http://www.forobd2tool.com/wp-content/uploads/2017/06/30/18-2.jpg

Step 2

Go to “READ KEY QUANTITY” first and it will show you the current key number.

In this case, this Ford Explorer already has 2 working keys.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/18-3.jpg
http://www.forobd2tool.com/wp-content/uploads/2017/06/30/18-4.jpg

Step 3

Back to choose “ADD KEYLESS” function.

And follow the tips, insert the new key fob into the car slot and turn on car ignition.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/18-5.jpg

Step 4

Then it start to program the new key. (Message show “ADAPTING SYSTEM, ABOUT 10 MINUTES”)

Wait 10 minutes and Car Key Programmer complete on time!

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/18-6.jpg
http://www.forobd2tool.com/wp-content/uploads/2017/06/30/18-7.jpg

It show “ADAPT FINISH” and current key number is 3.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/18-8.jpg
http://www.forobd2tool.com/wp-content/uploads/2017/06/30/18-9.jpg

Now SKP900 program Ford Explorer Keyless Remote successfully!

New key start car working… SKP900 do a good job!

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/18-10.jpg
P.S SKP900 Portuguese Version is also available!

Auto Diagnostic tool SKP900 Portugal

Xprog 5.76 vs Xprog M 5.70 vs Xprog Box 5.60 vs Xprog-M 5.5

Xprog-M programmer is updated to Xprog box v5.76!! So, what’s new in Xprog box 5.76 programmer & what’s the differences among xprog box (xprog m) v5.76 v5.70 v5.60 v5.5.

 

What is Similarities of Xprog-M programmers v5.76 v5.70 v5.60 v5.5?

Xprog m programmer v5.76 v5.70 v5.60 v5.5 all share the authorization as below:

 

AUTH-0001 Motorola HC05 family authorization (allows to read/write EEPROM)

AUTH-0002 Motorola HC08 family authorization (allows to read/write EEPROM)

AUTH-0003 Motorola HC11 family authorization (allows to read/write EEPROM)

AUTH-0004 Motorola HC12, 9S12 family authorization (allows to read/write EEPROM and flash memory)

AUTH-0005 Texas Instruments TMS370/TMS374 family authorization (allows to read/write EEPROM)

AUTH-0006 Motorola HC05Bxx and HC05Xxx family bypass security authorization (allows to read/write secured EEPROM and flash memory)

AUTH-0007 ST M35080 authorization. Read/Write/Erase device to delivery state.

AUTH-0008 BMW EWS3 authorization

AUTH-0009 ATMEGA family authorization (allows to read/write EEPROM and flash memory)

AUTH-0010 MB ZGS001 authorization

AUTH-0011 Motorola HC11EA9/E9 bypass security authorization (allows to bypass security bit and read EEPROM and RAM memory)

AUTH-0012 National CR16 authorization (allows to read/write EEPROM memory)

AUTH-0014 ST7, ST10 family authorization (allows to read/write internal flash)

AUTH-0015 MPC5xx authorization (depending on device program automatically detects MPC5xx, M95xxx device type, flash, external flash and configuration memory size)

AUTH-0018 Motorola HC12, HC912, MC9S12, MC9S12X bypass security authorization (allows to read/write secured EEPROM and flash memory)

AUTH-0020 ARM (Micronas, …) Family authorization (allows to read/write internal flash and external serial EEPROM)

AUTH-0021 ARM (Micronas, …) Family bypass security authorization (allows to read/write secured and non-secured internal flash and external serial EEPROM, view/change mileage, Chassis number (VIN), serial number and PIN code).

AUTH-0023-1 MAC7xxx

AUTH-0023-2 XC23xx

AUTH-0024-1 MC9S12Cxx

AUTH-0024-2 MC9S12XE

AUTH-0024-3 9S12XE SECURITY

AUTH-0024-4 MC9S12HA/HY/P

AUTH-0025-1 MPC/SPC5xxx Authorized 11/4/2014

 

 

 

What is Differences bettween Xprog-M box v5.76 v5.70 v5.60 v5.5

 

Xprog box 5.76 adds new authorization:

(More fucntions are coming soon)

 

MCU/MPU->infineon{XC16x}->SAK-XC164CS-16F

MCU/MPU->FresscaleHC08-Updated->MC68HCx08AS/AZ32_CONFIG

MCU/MPU->FresscaleHC08-Updated->MC68HCx08AS/AZ32_CONFIG

MCU/MPU->Fresscale9S08->MC9S08AW8_FLASH

MCU/MPU->Fresscale9S08->MC9S08AW8_FLASH

MCU/MPU->Fresscale9S12XD->MC9S12XDx128_EFPROM

MCU/MPU->Fresscale9S12XD->MC9S12XDx128-EFPROM-secured

MCU/MPU->Fresscale9S12XF->MC9S12XF128_EEE

MCU/MPU->Fresscale9S12XF->MC9S12XF128_EEE

MCU/MPU->Fresscale9S12XHY->MC9S12XHY128_D-FLASH

MCU/MPU->FresscaleMPC55xx->MPC5515_Code-Flash

MCU/MPU->FresscaleMPC560x->MPC5602B/C_Code-Flash

MCU/MPU->FresscaleMPC560x->MPC5602B/C_Code-Flash

Immobilizers->Yamaxa->T-MAX_TYPE_I_9S12T64

Other ECU ->Chrysler-DodgeJeep->BCM-GRAND_CHEROKEE_WK_2014_Flash

Other ECU ->GM ECU->SAF-XC164CS-16F

Other ECU ->HONDA Bikes->CB650F 2015_Code_Flash

Other ECU ->Renault ClioOther ->EPS_ST10F269

Other ECU ->Renault Modus ->ECU_SAK-XC164CS-32F

Airbag(XC2xxx)->FR3T-14B321-AF(XC2336A-72)->FR3T-14B321-AFflash0

Airbag(SPC560xx)/MPC560x)->Honda_CR-V(SPC560P50LS)->Code_Flash

 

XPROG v5.70 adds new MCU/MPU:
MCU/MPU->infineon{XC16x}->SAK-XC164CS-16F

MCU/MPU->FresscaleHC08-Updated->MC68HCx08AS/AZ32_CONFIG

MCU/MPU->FresscaleHC08-Updated->MC68HCx08AS/AZ32_CONFIG

MCU/MPU->Fresscale9S08->MC9S08AW8_FLASH

MCU/MPU->Fresscale9S08->MC9S08AW8_FLASH

MCU/MPU->Fresscale9S12XD->MC9S12XDx128_EFPROM

MCU/MPU->Fresscale9S12XD->MC9S12XDx128-EFPROM-secured

MCU/MPU->Fresscale9S12XF->MC9S12XF128_EEE

MCU/MPU->Fresscale9S12XF->MC9S12XF128_EEE

MCU/MPU->Fresscale9S12XHY->MC9S12XHY128_D-FLASH

MCU/MPU->FresscaleMPC55xx->MPC5515_Code-Flash

MCU/MPU->FresscaleMPC560x->MPC5602B/C_Code-Flash

MCU/MPU->FresscaleMPC560x->MPC5602B/C_Code-Flash

Immobilizers->Yamaxa->T-MAX_TYPE_I_9S12T64

Other ECU ->Chrysler-DodgeJeep->BCM-GRAND_CHEROKEE_WK_2014_Flash

Other ECU ->GM ECU->SAF-XC164CS-16F

Other ECU ->HONDA Bikes->CB650F 2015_Code_Flash

Other ECU ->Renault ClioOther ->EPS_ST10F269

Other ECU ->Renault Modus ->ECU_SAK-XC164CS-32F

Airbag(XC2xxx)->FR3T-14B321-AF(XC2336A-72)->FR3T-14B321-AFflash0

Airbag(SPC560xx)/MPC560x)->Honda_CR-V(SPC560P50LS)->Code_Flash
XPROG-M v5.60 ECU Box adds new EEPROM / MCU/ECU:

 

9S12XEP768 P-FLASH, D-FLASH, EEPROM (AUTH-0024-2)
9S12XET256 SECURITY P-FLASH, D-FLASH, EEPROM (AUTH-0024-3)
9S12XEQ384 SECURITY P-FLASH, D-FLASH, EEPROM (AUTH-0024-3)
9S12XEP768 SECURITY P-FLASH, D-FLASH, EEPROM (AUTH-0024-3)
9S12XEP100 SECURITY P-FLASH, D-FLASH, EEPROM (AUTH-0024-3)
XC2361A-56 FLASH3  (AUTH-0023-2)
MC9S12XDP512 0M23S
MAC7241 write bug fixed (AUTH-0023-1)….
Xprog-m V5.5 supports IC device list:

MCU/MPU  SPC560 serial

SPC560P44Lx_Code_Flash
SPC560P44Lx_Code_Flash_Test
SPC560P44Lx_Code_Flash_Shadow
SPC560P44Lx_Data_Flash
SPC560P44Lx_Code_Flash_Block
SPC560P50Lx_Code_Flash
SPC560P50Lx_Code_Flash_Test
SPC560P50Lx_Code_Flash_Shadow
SPC560P50Lx_Code_Flash
SPC560P50Lx_Code_Flash_Block

Freescale MPC5xx

MPC
MPC->Configuration-A
MPC->Configuration-B
MPC->External Flash
MPC->External EEPROM M95xxx

MCU/MPU

Freescale 9s12XHY

MC9S12XHY256 D-Flash
MC9S12XHY256 P-Flash

Freescale (Mac7xxx)

MAC7111VAG50_Flash
MAC7111VAG50_Data_Flash
MAC7112VAG50_Flash
MAC7112VAG50_Data_Flash
MAC7116VAG50_Flash
MAC7116VAG50_Data_Flash
MAC7131MVF_Flash
MAC7131MVF_Data_Flash
MAC7241VAF64_Flash
MAC7241VAF64_Shadow_Flash
MAC7242VAF64_Flash

Freescale 9S12XS-secured
MC9S12XS128_D-Flash-Secured
MC9S12XS128_P-Flash-Secured

This is about Xprog box v5.7.6

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/13-1.png

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/13-2.png

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/13-3.png

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/13-4.png

Xprog box 5.76 reviews.

Tested on HC912D60 the fucntion is okay..
For over an hour Xprog was connected to a PC, internet active, I have no problem with the certificate.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/13-5.png

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/13-6.png

Today tested on ST10F269 (ZBR2 MAN), multiple reading.
Internet access was off.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/13-7.png

After compared all version of Xpro-m,the customers know Xpro-M very well now,so the customers can choose the Xpro-m according to thire own requirment.

 

 

How to Adjust Mileage for Volvo S80 2008 with OBDSTAR X300M

OBDSTAR X300M Odometer Adjustment is a professional tool only for odometer adjustment, it can work with most world famous brand vehicles via OBDII. Here is tutorial about adjusting mileage for Volvo S80. Hope it helps users.

Vehicle: Volvo S80 2008

Current mileage:

Connect X300M with S80
http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-1.jpg

Select “Vehicle”

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-2.jpg

Select “MILEAGE ADJUSTMENT”

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-3.jpg

Then choose your vehicle model: “OTHER MODELS” -> ”OTHER MODELS V30.51”

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-4.jpg

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-5.jpg

It is loading…

Initializing…

Authorizing…

Then find “Volvo” -> “S80” -> “07-”

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-6.jpg

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-7.jpg
Choose “Mileage adjustment”

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-8.jpg

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-9.jpg

Switch ignition on

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-10.jpg

Switch ignition off and press ENT to continue

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-10.jpg

OBDSTAR X300M is reading mileage…

Then it will prompt you to input the name of file to save

After that, press ENT

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-11.jpg

It will remind you to confirm current mileage

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-12.jpg

Next, input the mileage of the adjustment and press ENT

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-13.jpg

OBDSTAR X300M is adjusting mileage…

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-14.jpg

Operation success!

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-15.jpg

Turn ignition on and see the changed mileage

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/8-16.jpg

How to repair BMW 328xi E90 window regulator by Autel MS908P?

The story is that: a 2006 BMW 328xi E90 rear right window was not working, replaced window regulator but it was stuck not all the way up and down. Used Maxisys MS908P to repair window regulator OK! So share this success case here.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-1.jpg

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-2.jpg

How Autel MS908P initialize BMW window regulator, reset BMW auto window?

Plug the Autel Scanner J2534 ECU Programming Device into car OBD port. Then you can use it to connect Autel MaxiSys Pro MS908P with car via Wi-Fi.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-3.jpg

Click “Diagnostics” and choose “BMW”.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-4.jpg

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-5.jpg

Or you can directly click the VIN button at left upper corner, choose “Auto detect” and it will read VIN automatically and show vehicle information.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-6.jpg

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-7.jpg

Now you need to connect car with power charger over 12V. Then put remote key into key slot and press car Start button.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-8.jpg

Then go to “Hot Function”.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-9.jpg

Choose “Window, door and roof” then “Initialize window regulators” function.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-10.jpg

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-11.jpg

Follow the tips “Switch on terminal 15 (ignition)”, keep remote key in key slot and do not press the brake pedal, press car Start button to turn ignition to terminal 15.

Choose to initialize the “Passenger’s side, rear” window regulator.

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-12.jpg

The rear right window will automatically open and close.

After that you can roll up and down that window normally.

Autel Maxisys Pro MS908P successfully initialize BMW 328xi E90 rear right window regulator! BMW auto window reset OK!

http://www.forobd2tool.com/wp-content/uploads/2017/06/30/3-13.jpg

Autel MS908P Authorization Check Failed Error Code 3 (solved)

http://forobd2tool.com/wp-content/uploads/2017/06/22/24-1.jpg

This is the solution of “Authorization Check Failed” with fault 3 on Autel MaxiSys MS908P Diagnostic system.

error message:

Authorization Check Failed!

Error Code 3

http://forobd2tool.com/wp-content/uploads/2017/06/22/24-2.jpg

Causes:

If you changed language, you can get this error

How to solve MS908P Authorization problem:

connect to the internet

log in PC Suit upgrade tool on networked computers

Obtain authorization automatically

If this serial number to determine the corresponding Autel ID, you can contact technical support queries.

Hope this helps those autel MS908P users by CnAutotool.com!

How Renault Can Clip reprogram a fuel injection ECU?

http://forobd2tool.com/wp-content/uploads/2017/06/22/18-0.jpg

Renault can clip is not only a scanner and diagnostic tool, but it also has some special functions like reprogram Renault ECU. This blog will show you how Renault clip reprograms a fuel injection ECU step by step.

How Renault CAN Clip diagnostic interface re-flash/code Renault injector ECU?

Step1. Install Renault CAN Clip diagnostic software. CAN Clip V168 at CnAutotool is the newest version now.

Step2. Connect CAN CLIP interface with vehicle via OBD socket. Select the reprogramming page. Obtain the VIN of the vehicle automatically. Select the reprogramming button.

http://forobd2tool.com/wp-content/uploads/2017/06/22/18-1.jpg

Step2. Click “SELECT THE COMPUTER TO BE PROGRAMMED” then “SELECTION” then click validate.

http://forobd2tool.com/wp-content/uploads/2017/06/22/18-2.jpg

Step3. Input the Repair Order and the vehicle Technical Specification code then click validate. After that make sure two things done: 1. Connect battery charger to the car. 2. Plug Can Clip Renault into the mains.

http://forobd2tool.com/wp-content/uploads/2017/06/22/18-3.jpg

Step4. There will be a tip “Select programming mode”, choose “CD-ROM”.

http://forobd2tool.com/wp-content/uploads/2017/06/22/18-4.jpg
Step5. Select the number for the software to download depending on the recorded operation commons, then confirm, then click “Software reference” and press Validate

http://forobd2tool.com/wp-content/uploads/2017/06/22/18-5.jpg

Step6. Input vehicle AFTER SALES REPROGRAMMING CODE then press Validate.

http://forobd2tool.com/wp-content/uploads/2017/06/22/18-6.jpg

Here you need use Renault Pin Extractor to calculate AFTER SALES REPROGRAMMING CODE by request code. Here is the Renault Pin Extractor Zip file for you:

http://www.cnautotool.com/goods-162-Best+Quality+Renault+CAN+Clip+Diagnostic+Interface+V151+with+Bluetooth.html

http://forobd2tool.com/wp-content/uploads/2017/06/22/18-7.jpg

Now it is programming. Please remember no operation on the vehicle or on the tool. This procedure will last for 5 minutes. Wait until the procedure is complete

http://forobd2tool.com/wp-content/uploads/2017/06/22/18-8.jpg
Then reprogramming is done! Return to the home page and save result. Next exit the Professional Diagnostic Tool CAN Clip software.

How to add a new language to Renault clip diagnostic software

This is how to add a new language to Renault clip software (newest version: CLIP V168). Renault clip diagnostic software needs the Serbian or Croatian language.

This is installation of renault clip on the Serbian or Croatian language.

In Renualt CLIP program, the description has Serbian Croatian Russian….. etc languages, and there are the Serbian or Croatian language files on the disc

So, how to installrenault clip on the Serbian or Croatian language?

The solution is in XP, Control Panel, Region and Language options, Regio Format set to Croatian, Home Location set to Croatian, at Tab Administrative, set Current system locale to Croatia, restart your PC and try install and you will see you have now Croatian language for choosing at installation

If you have the next message: “The current clip language is not supported by this version of the CD. To install this CD you must first uninstall the current version.
End of processing.”

The solution is- Try to make system restore before you tryed to install CAN Clip for Renault
Than, make a region and language settings to Croatian and after that try to install, If you cant do that,install on language that it asks,probably EN, than uninstall, CHANGE REGIONAL SETTINGS to Croatian and than try again.

That is, just change your settings in your PC to local language. (Croation or Serbian)

Now, Renaultcan clip diagnostic interface can be used in English, German, Danish, Spanish, Finnish, French, Italian, Norwegian, Dutch, Portuguese, Romania, Swedish, Croation andSerbian.

How to unlock radio code and use vin relearn by gm tech 2?

Here is the step-by-step instruction on clear radio theftlock for GM (GM, SAAB, OPEL, SUZUKI, ISUZU and HOLDEN) models with GM Tech 2 scan tool from CnAutotool.com.
Tools needed:
GM Tech2 diagnostic scan tool
Candi interface
http://forobd2tool.com/wp-content/uploads/2017/06/22/8-1.jpg

Tech II Theft-lock procedure:
Well setup CANDI module with GM Tech2 Scanner main unit, connect Tech2 scanner with vehicle
1.Select “Diagnostics” at the Main Menu screen
2.At the “Vehicle Identification” screen, select the following options:
– Model Year >>> (radio came from an 04 Escalade or whatever)
–LD Trk, MPV, Incomplete;
3. Select “Body” at the “System Selection” Menu screen
4. At the “Vehicle Identification” screen, select the following:
–          Appropriate model
–          Appropriate Air Conditioning
–          Navigation Radio
5. Select “Navigation Radio” at the “Body” screen
6. Select “Special Functions” at the “Radio” screen
7. Select “VIN Relearn” at the “Special Functions” screen
8. At the “VIN Relearn” screen, the Tech2 will display “Do you want to clear radio theft information?”
9. To begin clearing, press the soft touch key on the top right of the scan tool. The scan tool will display “Clearing Radio Theft in Progress.”
10. Press “EXIT” on the scan tool and cycle the ignition.
NOTE:
1.The radio theft will learn the VIN. Without learning the VIN, the radio will display a locked message (LOC or LOCKED).
2.Another way is to see if the sound works by installing the radio, and not turning the key to ON, just ACC. that will work the radio for a test.

How to Program Cadillac key fob with GM Tech2 clone

This is an instruction on how to program key fob to 2007 Cadillac CTS-V using a gm tech2 gm diagnostic scanner

Model: 2007 Cadillac CTS-V

The process…here you go…

The key to be programmed

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-1.jpg

Insert the key and ignition on

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-2.jpg

The gm tech 2 scan tool power on

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-3.jpg

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-4.jpg

In the main menu, go to Diagnostics

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-5.jpg

Select model: 2007 Cadillac D (DN) CTS-V passenger car

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-6.jpg

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-7.jpg

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-8.jpg

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-9.jpg

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-10.jpg
Then go to Vehicle Control Systems

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-11.jpg

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-12.jpg

Read vehicle info

Engine type: (U) 6.0L V8 LS2

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-13.jpg

Go to Module Setup

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-14.jpg

Then Remote control door lock receiver

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-15.jpg

Program key fobs…

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-16.jpg

Two key fobs to be programmed

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-17.jpg

Tips of programming key fobs:

All key fobs must be programmed each time any one fob is programmed. To program,press and hold the LOCK and UNLOCK key fob buttons prompted by the TECH 2 at CnAutotool.com. Programming takes 15-30 minutes….

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-18.jpg

http://forobd2tool.com/wp-content/uploads/2017/06/22/3-19.jpg

Programmed complete and test it’s working.

Done!

Program Passat 4th IMMO Key with OBDSTAR X300 DP

Here is the instruction on programming VAG Passat 4th IMMO Key by using OBDSTAR X300 DP key programmer and OBDSTAR RFID Adapter (adapter chip reader for VAG 4th 5th IMMO function)

Guide:
Dissemble the dashboard instrument
Connect OBDSTAR X300 DP with VCI and Dash
Turn ignition on (If it is the smart key, turn ignition OFF then turn it ON)

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-1.jpg
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-2.jpg
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-3.jpg

Make sure dash instrument is black

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-4.jpg
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-5.jpg

Reading eeprom data
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-6.jpg
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-7.jpg

Save data
Read IMMO data
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-8.jpg

Turn ignition on (If it is the smart key, turn ignition OFF then turn it ON)
Make sure dash instrument is black
Read VIN, CS code and PIN and key info

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-9.jpg
Select Generate OEM Dealer Key (Can start car)
Turn ignition on
Connect OBDSTAR RFID adapter with X300 DP

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-10.jpg
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-11.jpg

Insert the original key (chip) into RFID adapter

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-12.jpg
http://forobd2tool.com/wp-content/uploads/2017/06/14/18-13.jpg

RFID Indicator flashes, remove the first key chip
Follow X300 DP prompt to insert second key chip
RFID indicator flashes, reading key data
dash indicators turn on

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-14.jpg

Generating dealer key in progress

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-15.jpg

Generate dealer key success

http://forobd2tool.com/wp-content/uploads/2017/06/14/18-16.jpg
Test the new key, it works!