What Does it Mean & How Do I Figure Out What it Is

10

We have all had our check engine light come on and think the worst. Well just because the light came on doesn’t mean there is a monumental disaster around the corner. In fact, most of the time, it is something small such as a faulty o2 sensor or your gas cap is on incorrectly. There are two different ways your check engine light warns you. First is a steady light; this indicates not an emergency, but still important enough to make an appointment. Second is flashing, this usually means there is a severe problem. If this happens, stop your vehicle immediately to avoid further damage. Don’t stress, you can find out exactly what is going on by using an (On Board Diagnostics) OBD2 Scanner, or you can go to your local auto repair shop.

An Auto Scanner Diagnostic Tool can help you retrieve the error codes that trigger your check engine light. These codes are defined specifically and are either (generic) universal or manufacture specific and there are five digits. I will explain them briefly below.
1st Digit: signifies the system the trouble code is related to.
B = Body C = Chassis P = Powertrain U = Undefined
2nd Digit: signifies whether it is manufacturer specific or generic.
1 = Enhanced (manufacturer specific) and 0 = Generic (the # not the letter “O”)
3rd Digit: signifies the sub system the code pertains to.
1 = Emission Management Air or Fuel 2 = Injector Circuit Air or Fuel 3 = Misfire or Ignition 4 = Emissions
5 = Idle Control & Vehicle Speed 6 = Output Circuit & Computer 7 = Transmission 8 = Transmission
What are the Most Common Check Engine Light Problems

There are a handful of problems that are the usual suspects of the dreaded Check Engine Light. The first being your gas cap. If it is not properly attached it can cause your check engine light to illuminate. The second culprit is your O2 sensor. If the sensor is malfunctioning or broken, it can effect your emissions and reduce gas mileage. Third would be your Mass Air Flow sensor. This Professional Automotive Diagnostic Tool is responsible for supplying the right amount of air to your engine allowing for proper fuel distribution. Spark Plugs are also a common factor when your check engine lite is on. Your spark plugs ignite the compressed gas within your engine, when there is spark plug failure damage to the catalytic converter can happen. Additionally it can affect your engines overall performance and fuel economy. Your check engine light can alert you to more problems than I have discussed here. So if you are experiencing check engine light problems check get the codes from an OBD II Scanner Tool or visit your local auto repair shop to diagnose your vehicle’s trouble codes.

The 5 Top Reasons You Need an OBD Scanner On Board

Empire auto care Car Services Repair

Many things that can go wrong with your car, even if it’s brand new. Sometimes an engine component will malfunction, and you’ll need to understand what’s happened to get it fixed. That’s where an OBD scan tool comes in.

An OBD scanner is a tool that mechanics, auto parts stores, and vehicle manufacturers use to test the mechanics and computer functions in a vehicle. The tool is plugged into your car or truck, then it scans the system for errors.

After that, the scanner provides detailed information so you know how to repair the problem. Sometimes, it’s as simple as ignoring the error message because it was triggered by mistake; other times, it indicates a serious issue with your engine.

Whatever the result of the scan, your OBD tool will give you valuable peace of mind as you drive. With winter in full swing and uncertain road conditions, the last thing you want is to be stranded in the cold.

In many situations, you’ll be very happy you invested in a handy scanner. Here are five of the biggest.

1. Check Engine Light Turns On

If you paid attention during driver’s education, you’ll recall there’s a variety of lights and indicators on the dashboard, but the scariest is the check engine light. When that indicator blinks on, you were told to pull over as soon as possible and get the problem diagnosed.

Typically, you need to head to the nearest mechanic shop or auto parts store to check the error code and plan for repair. There are a couple of problems with this approach, however.

The first is that you may be in a remote location without a store nearby. It could also be a weekend or the middle of the night, when none of these facilities are open.
You run a risk of damaging your vehicle if you continue to drive it with the check engine light on. In some cases, it could be a non-immediate problem such as a loose gas cap, but in others, it could be your spark plugs, which can lead to more serious damage the longer you drive.

When you have an OBD scanner, you can diagnose the problem wherever you are, whether a freeway shoulder in the middle of nowhere or your driveway. You can read the error code and learn whether it’s safe to drive the car to a mechanic, or you should call a tow to prevent further damage.

The check engine light is not something to trifle with, and your Professional Diagnostic Tool will give you quick and accurate answers.
2. Cold Weather Concerns

When the temperatures drop below freezing, several things can happen to your vehicle. The battery can die, gas caps can loosen, and your tire pressure can go haywire.

These conditions can cause all sorts of warning indicators to light up your dashboard, including the check engine light. Obviously, that’s cause for concern.

You can make sure your vehicle is in tip-top condition for driving with an OBD scan tool. Any time a warning light flickers on, you’ll have the tool stored in your glove compartment for easy diagnostics.

It will check for key indicators like warning lights, fuel system pressure, engine temperature, exhaust emission levels, throttle response, idle speed, and other key metrics that can show problems in colder temperatures.

Then you’ll know what to have repaired and whether the vehicle’s safe to drive.

3. Your Car or Truck Dies in the Middle of Nowhere

Usually, if your vehicle dies during a long drive, you won’t know the exact reason. By popping the hood, you’ll only see problems that are on the surface. Usually, you need diagnostics to see something deeper.

An OBD scanner can help. Although it might not render specifics about the cause of a malfunction, it can clue you into such things as fuel system pressure and battery levels. It will give you information that can be useful for determining your next step … and in some cases, you may be able to fix it on the spot.
4. You’re Strapped for Cash

The average American spends around 1.5 percent of annual income on auto repairs. That averages to about $600 per car in the U.S., but the number is just an average.

Many people end up spending thousands for vehicle repairs in a year because their vehicle is older and needs more care. The sad thing? Many of the most expensive vehicle repairs can be fixed at home if the owner has the right tools and a decent YouTube tutorial.

An Car Diagnostic Scanner is one of those essential tools, and you can get a decent one for as little as $20. If owning such a tool saves you $600 on car repairs because you were able to diagnose the problem and fix it yourself, you’ll be more than grateful you made the initial investment for a scanner.
5. Manufacturer Recalls

reasons you need a obd2 scanner

It’s always a little unnerving when you receive a letter or phone call from your vehicle manufacturer that reports a mass recall of your vehicle’s make and model. Usually, the recalls involve a small and harmless malfunction, but occasional outliers could inflict serious harm on you and the car’s occupants.

Your OBD scanner test for the problem. You can determine whether you should be concerned about your vehicle right away or it can wait a while for the repair. Some factory recalls can take months to address, and you don’t want to drive a car or truck that could “blow up” at any moment.

An Automotive Scan Tool is not only a practical investment, but it buys you peace of mind. For less than $100, you’ll have a car repair tool in your arsenal that will save you money and clue you in on potentially serious issues.
Contact the Scan Tool Center for More Information Today!

At the Scan Tool Center, we’re big supporters of purchasing a scan tool to keep in your vehicle. We recognize some of the problems that may occur if you don’t have the proper diagnostic and repair tools.

That’s why we’ve created a collection of reviews and quality information on scan tools and what they offer. For more background on the top OBD2 Scan Tools, contact us today!

23-1

What problems can there be with using OBD scan tools

Like in most tools, scan tools are not an exceptional category when it comes to having problems. At any given point, a tool is bound to fail. Most OBD scan tools are known to have some problems. These problems however are not usually open given the several benefits the users get from the OBD2 Scanner.

23-1

Looking at OBD I and OBD II tools, the level of experiences may be different depending on the nature of the check engine light fault. It is however notable that most scan tools have the following problems;

Updatability problems

This is not a universal problem though it is seen with most of the Car Diagnostic Tools of the old generation. Because of the compatibility issues, this range of scan tools known as readers will definitely not cover the requisite protocols. This makes them not to be able to scan newer car models.

It is however notable that with lack of updatable feature, the owner or technician may at times be forced to source for an alternative OBD scan tool. This is bound to cost money in terms of purchase of a new scan tool or the consultation of the mechanic.
Do you want know another information about OBD Scanner? Click link below

Read “The history of the OBD scans tools”

While the cost of purchasing some of the scan tools is relatively lower, it is seen as one of the biggest problem in most of the scan tools. Some OBD scan readers cost higher even if they do not cover the OBD protocols that are expected of them. In this regard, the cost function may even rise when such a machine forces the owner to seek the services of the mechanic.

USE

The use of most of the Launch X431 is rather simple compared to the past experiences. This may be true though the codes as they are referred to are in most cases not easy to understand to a beginner. The need for interpretation of the code meaning which in most cases takes the help of the mechanic could involve the use of substantial amounts of money.

In this case, what is usually believed to be convenient in terms of cost may turn out to be conduit for the mechanic making substantial amounts from the owner without having to sweat. In addition, some of the scan tools are hard to connect given the complicated requirements of the software may prove to be quite inconveniencing if you are not a software Guru.

In most cases, the OBD scan tools are purchased with prior research on the compatibility of the tool.  It may not be easy to know whether the tool will work or not. This is precisely because some of the scan tools promise to code on certain ranges but when put in practice, they fail miserably.

Package
23-2

The overall make of most of the OBD scan tools just looks perfect on the outside. However, the differences in terms of features and their covering scope may at times prove to be quite a challenge if you are a beginner.  It is in this regard that OBD tool packages are usually confusing and may make one to purchase an inappropriate tool.

The package issue is also one thing which is at the heart of the OBD scan tool debate. With the several parts in the package, the novice is usually put at a disadvantage if you are not well versed with how the parts work. For instance, if the tool works in the multilingual global dialects, then one has to know at least one. Not knowing this still makes one have the need for consultation.

OBD scan tool problems are not cast on stone and are bound to be corrected if the user is well informed. Most of this is found on the user manual. It is also good to learn how your car functions at the point of purchase because most cars are fitted with the tool at manufacture.

18-2

Tips on the OBD scan tool use

Learning how to use an Auto Diagnostic tool is an important part in ensuring that there is always a smooth fault repair process. Despite its importance, so many people are usually oblivious of this fact and end up just purchasing the OBD scan tool from the brick and motor stores or the online outlets and the commencing their use without passing through the learning process.

Such cases lead to some scanning mishaps or misinterpretation of the trouble codes which may have been coded. The user may end up incurring huge expenses which could have been avoided if the learning of how to use an OBD scan tool was taken seriously. Though the whole usage process is usually contained in the user manual, it is imperative to have a second opinion on how the scanner is used.

In this article, we have taken time to take you through a step by step process on how to use an OBD scan tool.  We are glad to have you take the journey of learning a step by step use of the OBD with us.
Check the car OBD compliance

It is important for you to look at the car OBD user manual and ensure that it is compliant with the requirements of the OBD regulations. Professional Diagnostic Tools was basically formed to control the rate of emission in the environment, its sensor based network with high efficiency raters if well used.
18-1

The OBD is a computer controlled interface which work with several sensors to give the user an indication on the state of the car engine health. Knowing the coding capacity enables the user to be able to select the relevant scan tool for the given car.

In most cases, cars which are OBD compliant have the tool already within its system and the car malfunction status is detected when the signal keeps giving what is in most cases known as the ‘check engine light’. This is in most cases assign of a fault within the car system and it can be anything spanning from the engine fuel fault, the car temperature status or just something else.

This fault detection usually arise from the fact that the car engine has what may be called the power train control module (PCM) which just guesses through its sensors what the car system ought to do.

The standard procedure with the Diagnostic Tools for Trucks scan process is that the PCM has the capacity to store trouble code data that is detected within the engine. In most cases, the code data deciphering require the service of a qualified mechanic and so you have to pull your car to the next motor mechanic for the trouble code assessment.

However, this is not the case with most of the scan tools of the modern times which have the trouble code directory where the data code meanings can be easily referred.
Plug in the OBD scan tool

The detection of the engine fault through the malfunction indicator light (M/IL) is enough to send you into action. The OBD connector for most vehicles is usually located below the driver’s seat. Using the 16 pin connection cable the scan tool is fitted to the cars diagnostic code port.

When the connection is established, the engine should always remain awake but care should be taken not to turn the key on. The plug in usually allows the OBD scan tool to display certain basic information regarding the car.

If the OBD scanner in question is a Bluetooth one, it will be important to pair it with the relevant OBD interface found within the car on board diagnostic software function. Most of the Bluetooth devices are fast and use a wireless interface. Some of the scans in this category have special software called the OBD wiz and works faster.

The important thing is having a relevant software pairing device in the form of a phone, an iPhone or iPad with the relevant android or iOS applications or windows laptop. These are made ready for pairing by down loading the OBD Bluetooth software relevant for the OBD scan tool in question.

The OBD display gives the driver options to scroll down and choose whether he wants to check trouble codes. The code detection process may take some time. Because some of the new generation OBD scanners are known for their level of sophistication, using them at this level may not be hard.
Select the relevant scroll down key

This option can either be in the form of enabling the car to detect only the codes or in most cases conduct a repair especially when the check engine light function is enabled. in some cases, to correct the trouble codes may require one to complete certain drive cycles till the car engine will detect the the problem has been fully corrected.
Check troble code step 1

Select the relevant scroll down key
Get the code readings

When the selection of the relevant keys are selected, the OBD display has the capacity of showing the codes and their meanings. Some of the tools which are more advanced have several display functions which includes the live data and the freeze data reading. The freeze data are stored data which is in most cases usable later.

The coded data reading is usually displayed on screen of the OBD scan for the mechanic or the user to see. However, in most cases, the new generation scanners have the option of the data being displayed on the screen of your desktop or laptop. The use of the new generation scanners is usually one area where the scan completion process can be well known. Don’t run the risk of wrong fault detection using some old model readers which in some cases masquerade as scanners.
What to do with the trouble codes

When the data has been coded using the do it yourself devices in the market, yet the check engine light trouble sign persists. Checking on any possible fault code sources through the data code readings on the screen is important. In some cases, it is imperative to consult a qualified mechanic top see if the problem could be arising from other areas.

Users may not be aware that the malfunction indicator light may remain on and off to signal some loose connection in some engine area. Though the whole process may cost a lot, the mechanic may have a professional opinion on what is making the malfunction indicator light to persist. Moreover, the mechanic may know how to translate the codes if the tool is not fitted with the necessary code translation guides.

OBD scan tools differ in shape, the amount of data which they can code; the use of the new generation diagnostic scanner may prove to be a convenient affair. Though the other older readers are also usable, it is in most cases notable that they may not cover as much data as the new generation scan tools

3-1

OBD2 Scanner You Can Use in the Car

There is a chance that you would like to keep your car working properly at all times and although you may try to check it as often as you like, there are times when you will not be able to detect a few things that an OBD scanner may have been able to detect if only you have one. Your check engine light may be on but you are not quite sure what the main problem is. The right OBD scanner can give you the help that you need.

If you are on the lookout for the right professional automotive diagnostic tools, you have to remember that there are different ones available. Choosing the right one can be a bit of a hassle if you do not have any idea about the things that you should look for in OBD Scanners. Hopefully, by the time that you finish reading this article, you will have a clearer idea of the OBD Scanner that you want.OBD2 Scanner You Can Use in the Car

Why Purchase an OBD2 Scanner

At this point you may be thinking that you do not need an OBD2 Scanner because you can easily bring your car to the nearest repair and diagnostics shop and have your car diagnosed but can you imagine how much those simple tasks will cost? It can cost you a lot of money and this is not a good thing if you do not have a budget.

Just imagine if you would need to take an emissions test and you know that you will fail because you cannot determine what is wrong with your vehicle. The use of the OBD2 Scanner will help you with the things that you need. It will help you with what you want. It is only through this that you will be able to determine what is wrong with your car and rightfully fix it before your car undergoes the test.
How to Choose the Right OBD2 Scanner

In order to have an effective OBD Scanner that will fit your needs, you have to consider a few things such as the following:

Consider if the OBD Scanner is Compatible with Your Vehicle: You have to remember that not all OBD Scanners will be able to read all types of vehicles. Since you already know what your vehicle is, you can easily eliminate all OBD scanners that will not be useful for you.
Consider the Various Features of the OBD Scanner: What are the different things that the OBD Scanner can offer? Can it check your whole engine? Can it also check your brakes and your battery? You have to consider this well because if the OBD Scanner that you purchase will not have those features available, you will probably not feel happy with the results that you will get. Plus, you will not know for sure what is causing your car problem.
Consider Your Budget: There may be some OBD tools that seem great and perfect for all of your needs but there is one simple problem – you cannot afford it. If this is the case, you have to remember that knowing your budget can be essential. It does not mean that just because you cannot afford an expensive product, what you are going to buy is already of lesser quality. No matter what your budget is, you will find the right OBD tool for you.
Remember Your Purpose: Would you like to have an OBD2 Scanner that can provide more than the basic things that you may need to know about? There may be some scanners that you can use to check your airbags and sometimes even your record player that you use in your car. It does not matter if you have the best record player if it does not work. Your scanner will be able to give you the proper details that you need.

Some OBD2 Scanners You Can Try

Since there are a lot of scanners that you may find in the market, narrowing down your search can be a complicated task. Here are some of the items that you may want to consider:
Autel (MaxiScan MS309) OBD-II Code Reader1. AutelMaxiscan OBD – II Code Reader and Scan Tool

If you are looking for an  ECU Programmer that you can operate without any issues, this is the right one for you because it is simple. You can be sure that you will be able to work it easily in order to check the possible reasons why your check engine light has lighted up. Since this is also sold cheaply, it is recommended that you use this for your personal use. This will make figuring out what’s wrong with your car easier to accomplish.
AutelAutolink AL619 ABS/SRS CAN OBD2 Code Scanner2. AutelAutolink Al619 ABS/SRS CAN OBD2 Code Scanner

If you are considering price range and also all the different features that the OBD2 scanner can give, this may be the perfect one for you to choose. This can be used for multiple cars so there is a big chance that you do not need to purchase separate ones for your different vehicles. If you are worried about the language, no need to worry about this too because this comes in several languages that will help you understand the diagnosis easily.

Do remember that there may be some special features that you are looking for in OBD2 Scanner. For instance, you may search for a scanner that may also serve as a record player. There are always different ones that are available.
INNOVA 3160 Diagnostic Scan Tool3. Innova 3160 Diagnostic Scan Tool

If you are looking for a product that is advanced in nature, this is the perfect scan tool for you to try. Since this is advanced, it can provide not only the basic details that you need but also give proper details about your brakes. There may be times when you have to update it. You have to be updated with the use of the Internet from time to time.
Conclusion

From being able to be like a record player and to check up the various important components of the car, an OBD2 Scanner can be a useful tool that every car owner should have. It is not enough that professionals have this scanner. You can benefit a lot with the use of this tool. Just make sure that you will pick the right one.