SDconnect C4 Software Released Notes

Since 12.2017, DTS-Monaco and Vediamo were added to 12.2018 SD connect C4 software. That is the biggest difference from old versions (CnAutotool.com).

12.2018 XENTRY/DAS Released Notes:

DAS Standalone Activated.

W(2014) Activated in DAS.

Offline Programming Activated.

LKW EOL OFFLINE MENU & VMAX for Tucks activated.

Smart Cars VIN reconfiguration PassFree Activated.

Added SMART 451 & 454 OFFLINE KEY TEACH-IN program

Added Development Data & Development Data (inside control unit adaptation) SAM451(SMART)

Added Development Data & Extra Coding(inside control unit adaptation) ESP451(SMART)

Added Development Data and Read coding-string in ESP 454

Add extra functions: Writing VIN & Development Status (inside control unit adaptation).

Audio Video Navigation and telematics – add Dev menu in DAS COMAND APS menupurpose: Add developer menu in DAS Command APS menu.

Audio Video Navigation and telematics – HU Exchange Audio 50 to COMAND password free

purpose: No password required, F3 to continue.

DAS Special Function Password Free PKW and SMART. special functions, e.g AB or ABR ecu in DAS W204, you are asked to insert password. With this system, you can enter any character, minimum “1” and F2 to continue.

Erase SCR/ADBLUE fault code (in MR) with correct New FDOK XN.

– Erasing of emission-relevant (SCR/ADBLUE) fault code: No need FDOK encrypted random number, F3 to continue.

Calculate correct nueu-FDOK XN internally, and change the encrypted random number to correct one in memory

Collapse

NFZ SonderFunktion Password Free purpose: password free for NFZ when doing SonderFunktion (Flash/Programming).

Nox Torque Limit Setting (FR/CPC0) with correct New FDOK XT

purpose:

– Nox Torque limit Setting: No need FDOK encrypted random number, F3 to continue

– Calculate correct nueu-FDOK internally, and change the encrypted random number to correct one in memory

– Added value: UNLOCK Legal speed limit direct edit without going to special function

Special Function Password Free Transporter

-purpose: Special Function Password Free for Transporter

TRANSMISSION or GETRIEBE – EGS1 Special Function password free

purpose: No password required, F3 to continue.

TRANSMISSION or GETRIEBE – EGS2 Diagnosis Routine password free

purpose: No password required, F3 to continue.

12.2018 Xentry/DAS 100% Tested with SD connect C4:

22-1
22-2
22-3
22-4
22-5

2018A Version CAT Caterpillar ET Diagnostic Adapter III PLUS DELLd630 laptop (Real Caterpillar ET3 Adapter III)

we will install the software before ship, so you can get it work directly after you receive it.

2018A Cat ET software as Cat Caterpillar ET 2015A Software update version, 2018A Caterpillar Electronic Technician softwarer With CAT ET 3 Cat caterpillar adapter 3 support caterpillar diagnostic till 2018.

13-1

Cat et Caterpillar Electronic Technician Software 2018A V1.0:
Type of catalogue: Caterpillar Electronic Technician Diagnostic Software
Make: Caterpillar
Region: WorldWide all region
Inclusive languages: English, Chinese, Danish, French, German, Italian, Japanese, Portuguese, Russian, Spanish

Caterpillar ET Software 2018A Function:
This diagnostic app allows you to:
View active and logged diagnostics.
View events where irregularities occurred and were logged by the ECM.
View the status of a group of parameters (temperatures, pressures, etc.) simultaneously.
Record and log performance data.
Graph a group of status parameters.
View the current configuration of an ECM.
Change ECM configurations.
Perform diagnostic tests.
Perform calibrations.
Print reports and diagnostic results.
Please keep in mind that some ecm settings for example, speed limit requires factory password. The factory password generator is not included in this application
Package :
1.Used Dell D630 laptop
2.Real CAT et3 Comm Adapter III(it’s best quality cat et 3,not adapter 2,please check Communication port)
3.USB Cable (From device to your computer)
4.J1939/J1708 Cable (from device to your truck)

Original Factory Caterpillar ET3 Adapter III Compare With OEM Caterpillar ET Diagnostic Adpater III
1. Original Factory CAT ET can use once pluged, no need install the USB drive, the software can automatic realize it for ET3 Adapter, and the machine can automatic weld the high quality Circuit board, quality will be more reliable.

2. The OEM Caterpillar ET Diagnostic Adapter III need use USB Drive to install, and need choose the COM Port, and  in the software ET also need choose ET2 then can be used.

The Details as follows:
13-2
13-3
13-4

Package 1 :
1.Used Dell D630 laptop
2.Real CAT et3 Comm Adapter III(it’s best quality cat et 3,not adapter 2,please check Communication port)
3.USB Cable (From device to your computer)
4.J1939/J1708 9PIN Cable (from device to your truck)
5.6PIN Cable (for old truck)
13-5

Package 2:
1.Used Dell D630 laptop
2.Real CAT et3 Comm Adapter III(it’s best quality cat et 3,not adapter 2,please check Communication port)
3.USB Cable (From device to your computer)
4.J1939/J1708 9PIN Cable (from device to your truck)
5.6PIN Cable (for old truck)
6.14PIN Cable(for new truck,optional)

13-6

How to configure Xentry Connect C5

2018 Xentry Connect C5 user manual: how to configure/set up MB SD Connect C4/C5 to use for the first time

Please have your XENTRY Connect MAC addresses (Wi-fi and LAN) enabled for the workshop network byyour IT supervisor/IT service provider in advance. You can read off theMAC addresses (Wi-fi and LAN) from the stickers on the devices.
3-1

Your case already contains a printed empty network questionnaire.

Please have it filled out by your IT supervisor. Important! Do notcontinue the initial startup until the questionnaire has been filled outcompletely! This will help to avoid additional work.
3-2

The latest Mercedes diagnostic software disk came with your MB SD Connect C5.

You can start the network configuration now.

Completely charge and turn on the XENTRY Connect.

Starting the XENTRY Connect for the first time can take up to 10 minutes.

Configuration can be started whilst both devices are still charging.

Attention! Be sure to use the correct power supply units!

Start the XENTRY Control software using the desktop link on the laptop. ConfigAssist is already open; if not,call up ConfigAssist via the “Configuration” menu.

Note! If you work with static IP addresses, you must perform theconfiguration via the expert dialog and transfer the configuration tothe XENTRY Connect via a USB stick.

3-3
Please have the filled out network questionnaire on hand:

How would you like to configure the devices?

Select one of the 3 options.

Recommended selection: “New without existing configuration data”.

3-4

Please continue following the ConfigAssist dialogs and enter the required

data from the network questionnaire.

Next, switch on the XENTRY Connect. This has already finished installing.
3-5

In the final steps, the configuration is transferred from the laptop to the XENTRY Connect. You will be prompted to interconnectthe devices using the supplied black Ethernet connecting cable.

This cable connection is required only for configuration

If configuration is successful, a green tile with the number of the Benz diagnostic tool XENTRYConnect C5will be displayed. You can now use the devices: Remove theblack Ethernet connecting cable to work via WLAN and with an onlineconnection. Then click on the green tile in order to read out the datafor ordering the StartKey.
3-6

Done!

How to configure Xentry Connect C5

2018 Xentry Connect C5 user manual: how to configure/set up MB SD Connect C4/C5 to use for the first time

Please have your XENTRY Connect MAC addresses (Wi-fi and LAN) enabled for the workshop network byyour IT supervisor/IT service provider in advance. You can read off theMAC addresses (Wi-fi and LAN) from the stickers on the devices.
3-1

Your case already contains a printed empty network questionnaire.

Please have it filled out by your IT supervisor. Important! Do notcontinue the initial startup until the questionnaire has been filled outcompletely! This will help to avoid additional work.
3-2

The latest Mercedes diagnostic software disk came with your MB SD Connect C5.

You can start the network configuration now.

Completely charge and turn on the XENTRY Connect.

Starting the XENTRY Connect for the first time can take up to 10 minutes.

Configuration can be started whilst both devices are still charging.

Attention! Be sure to use the correct power supply units!

Start the XENTRY Control software using the desktop link on the laptop. ConfigAssist is already open; if not,call up ConfigAssist via the “Configuration” menu.

Note! If you work with static IP addresses, you must perform theconfiguration via the expert dialog and transfer the configuration tothe XENTRY Connect via a USB stick.

3-3
Please have the filled out network questionnaire on hand:

How would you like to configure the devices?

Select one of the 3 options.

Recommended selection: “New without existing configuration data”.

3-4

Please continue following the ConfigAssist dialogs and enter the required

data from the network questionnaire.

Next, switch on the XENTRY Connect. This has already finished installing.
3-5

In the final steps, the configuration is transferred from the laptop to the XENTRY Connect. You will be prompted to interconnectthe devices using the supplied black Ethernet connecting cable.

This cable connection is required only for configuration

If configuration is successful, a green tile with the number of the Benz diagnostic tool XENTRYConnect C5will be displayed. You can now use the devices: Remove theblack Ethernet connecting cable to work via WLAN and with an onlineconnection. Then click on the green tile in order to read out the datafor ordering the StartKey.
3-6

Done!